Craftsman 172.417710, Operator'S Manual

Page: 6 / 8

9
REPLACING A BIT
If the bits in the Bit Cartridge need to be
replaced, remove Bit Cartridge by pulling the
Slide button back and pushing the Bit
cartridge through the left window. Replace the
bits with the desired bits. Ensure the bits
are properly positioned in the Cartridge and
are not protruding from the back of the Bit
Cartridge. Or simply pull a worn or broken
bit from the chuck and replace it with a new
one. It will load into the Cartridge
automatically when the Slide button is
pulled back. (See Fig. 5).
NOTE:
1) Only 25 mm bits are compatible with the screwdriver.
2) If the Slide button is not pulled back fully, the Bit Cartridge will get stuck when
taking it out from the tool. Pull the Slide button all the way back.
3) The Slide button may not fully push forward if the bit cartridge is not properly
aligned inside. Make sure the bit cartridge has clicked into place when selecting
the desired bit to use. If the Slide button cannot properly be pushed forward, just
turn the bit cartridge slightly clockwise or counterclockwise and try again.
OPERATING INSTRUCTIONS cont.
(Fig. 5)
(Fig. 6A)
(Fig. 6B)
EXTENSION SHAFT
Use the extension shaft to extend the reach of the screwdriver into recessed
areas. To insert extension shaft into screwdriver, select the bit you need to
extend and push the slide button forward to engage it. Then, using your
thumb and index finger, remove the bit and insert the extension shaft into
the screwdriver. Then load the bit into the extension.
WOBBLE BIT
The wobble bit is engineered to angle into
hard to reach corners and recessed areas
by swiveling inside of the chuck
(See Fig. 6B). To use the wobble bit, first
push forward and remove one of the bits
from the Bit Cartridge. Insert the wobble
bit directly into the chuck in place of the
removed bit.
The wobble bit may also be inserted into
the end of the extension shaft to extend
the reach of the screwdriver even
further into recessed areas.
10
WARNING: Never change the
direction of rotation when the Chuck
is rotating; wait until it has stopped!
!
FORWARD / REVERSE SWITCH
(See Fig. 7)
This switch changes the chuck bit rotation
direction. Push the top of the rocker switch
for driving forward and push the bottom for
removing screws/reverse.
FORWARD
REVERSE
FORWARD
REVERSE
OPERATING INSTRUCTIONS cont.
MAINTENANCE
FULLY AUTOMATIC SPINDLE
LOCKING (AUTO-LOCK) (See Fig. 8)
The screwdriver Chuck (Fig. 8) is locked when the
On/Off Switch (Fig. 7) is not pressed. This allows
the driver to be used manually when needed.
Important: When using as a manual tool,
do not press the On/Off Switch (Fig. 7).
Otherwise the screwdriver will be damaged.
USING THE LED LIGHT (See Fig. 9)
To turn on the light simply press the On/Off
Switch. When you release the On/Off
Switch, the light will be off.
LED light increases visibility and is great
for dark or enclosed areas.
PROTECTION AGAINST DEEP
DISCHARGING
The Li-ion battery is protected against deep
discharging by the “Discharging Protection
System”. When the battery is empty, the tool
is switched off by means of a protective
circuit: The chuck no longer rotates. When
this occurs you need to recharge the battery.
Your tool requires no additional lubrication or maintenance. There are no
user serviceable parts in your power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean with a dry cloth. Always store
your power tool in a dry place. Keep the motor ventilation slots clean. Keep
all working controls free of dust. Occasionally you may see sparks through
the ventilation slots. This is normal and will not damage your power tool.
(Fig. 8)
(Fig. 9)
(Fig. 7) (Fig. 7)