background image

page 8

Warranty.

Parts Replacement.

Problem: 

Fan fails to operate.

Solutions:

1. Check wall switch to fan.
2. Verify that reverse switch is set completely in either 
direction.
3. Check to be sure fan is wired properly.

Problem: 

Light kit (optional) not lighting.

Solutions:

1. Check wall switch to fan.
2. Check that bulbs are installed correctly.
3. Check to be sure wires in canopy are wired properly.
4. Verify that molex connections are connected 
properly in switch housing.

Problem: 

Fan operates but light(s) fail(s) (if 

applicable).

Solutions: 

1. Check that bulbs are installed correctly.
2. Check to be sure wires in canopy are wired properly.
3. Verify that molex connections are connected 
properly in switch housing.
4. Replace defective bulbs with same type of bulb.

Problem: 

Lighting source (up-light, down-light or 

both), if applicable, not functioning.

Solution:

Wattage Limiting Device has interrupted the flow of 
electricity to the light source. Ensure bulbs total no 
more than 190W in the light source. 

Problem: 

Fan wobbles.

Solutions:

1. Use the balancing kit provided in one of the 
hardware packs. 

If no blade balancing kit is provided, 

please call Customer Support,
1-800-486-4892, to request one.

2. Carefully loosen motor housing and verify that 
mounting bracket is secure. 
3. Check to be sure motor housing is turned 
completely and that motor housing screws are secure.

Troubleshooting.

CRAFTMADE/ELLINGTON LIFETIME WARRANTY:
CRAFTMADE/ELLINGTON warrants this fan to the 
original household purchaser for indoor use under 
the following provisions:
1-YEAR WARRANTY: CRAFTMADE/ELLINGTON will 
replace or repair any fan which has faulty 
performance due to a defect in material or 
workmanship. Contact Craftmade/Ellington Customer 
Service at

1-800-486-4892

 to arrange for return of fan. Return 

fan, shipping prepaid, to Craftmade/Ellington. We will 
repair or ship you a replacement fan, and we will pay 
the return shipping cost.
5-YEAR WARRANTY: CRAFTMADE/ELLINGTON will 
repair or replace at no charge to the original 
purchaser any fan motor that fails to operate 
satisfactorily when failure results from normal use.
RETURN FAN MOTOR ONLY, shipping prepaid, to 
Craftmade/Ellington. We will repair or ship purchaser 
a replacement motor and Craftmade/Ellington will 
pay the return shipping cost.
6-YEAR to LIFETIME LIMITED WARRANTY: 
CRAFTMADE/ELLINGTON will repair the fan, at no 
charge for labor only to the original purchaser, if the 
fan motor fails to operate satisfactorily when failure 
results from normal use. Parts used in the repair will 
be billed to the purchaser at prevailing prices at time 
of repair.
    The purchaser shall be responsible for all costs 
incurred in the removal, reinstallation and shipping of 
the product for repairs.
    This warranty does not apply when damage from 
mechanical, physical, electrical or water abuse results 
in causing the malfunction. Deterioration of finishes 
or other parts due to time or exposure to salt air is 
specifically exempted under this warranty.
    Neither Craftmade/Ellington nor the manufacturer 
will assume any liability resulting from improper 
installation or use of this product. In no case shall the 
company be liable for any consequential damages for 
breach of this, or any other warranty expressed or 
implied whatsoever. This limitation as to 
consequential damages shall not apply in states 
where prohibited.

For parts and information, please refer to
"Parts Inventory" on page 2.
Craftmade/Ellington Customer Support:

1-800-486-4892

www.craftmadebrands.com

WARNING: 

Failure to disconnect power supply 

prior to troubleshooting any wiring issues may 
result in serious injury.

Summary of Contents for FC52



















Reviews: