background image

 

6

                               

 

MODEL CX206 – 12” LEFT TILT TABLE SAW 

 

As part of the growing line of Craftex woodworking equipment, we are proud to offer CX206 -
12” Left Tilt Table Saw. The Craftex name guarantees Craft Excellence. By following the 
instructions and procedures laid out in this owner’s manual, you will receive years of excellent 
service and satisfaction. The CX206 is a professional tool and like all power tools, proper care 
and safety procedures should be adhered to.  
 
 

 Motor .............................................. 3-HP, 

220-V, Single Phase TEFC Motor 

 Blade 

Guard ................................... Riving Knife, CSA Approved & UL897 Compliant 

 Mitre 

Gauge.................................... T-Slot Mitre Gauge 

 Drive 

System .................................. Triple “V” Belt Drive 

 Rip 

Fence ....................................... “T” Type Heavy Duty Rip Fence (Cam Lever) 

w/Optical Cursor

 

 Arbor 

Extension .............................. Included 

 Arbor 

Tilt ......................................... Left Tilting 

 Table 

Size....................................... 30” x 48” (with Extension Wings) 

 Blade 

Speed ................................... 4,140 RPM 

 

Floor to Table Height ...................... 35” 

 

Maximum Depth of Cut @ 90 ° ....... 4” 

 

Maximum Depth of Cut @ 45 ° ....... 2 5/8” 

 

Dust Collection Ports ...................... One 4” Port  

 Base 

Dimensions............................  30” x 48” 

 Blade 

Size ...................................... 12” 

 Approximate 

Weight .......................  280 Kgs 

 

 
 

CX206–12” Left Tilt Table Saw 

 

FEATURES 

Summary of Contents for CX205




































Reviews: