Craftex CX119 User Manual Download Page 29

 

29

 

 

 
 

WARRANTY 

 
 
 

Craftex warrants every product to be free from defects in materials and agrees to correct such defects where 
applicable. This warranty covers 

three years

 for parts and 90 days for labour (unless specified otherwise), to the 

original purchaser from the date of purchase but does not apply to malfunctions arising directly or indirectly from 
misuse, abuse, improper installation or assembly, negligence, accidents, repairs or alterations or lack of 
maintenance.  

Proof of purchase is necessary

All warranty claims are subject to inspection of such products or part thereof and Craftex reserves the right to 
inspect any returned item before a refund or replacement may be issued. 
This warranty shall not apply to consumable products such as blades, bits, belts, cutters, chisels, punches 
etceteras. 
Craftex shall in no event be liable for injuries, accidental or otherwise, death to persons or damage to property or 
for incidental contingent, special or consequential damages arising from the use of our products. 

RETURNS, REPAIRS AND REPLACEMENTS 

To return, repair, or replace a Craftex product, you must visit the appropriate Busy Bee Tools showroom or call 1-
800-461-BUSY. Craftex is a brand of equipment that is exclusive to Busy Bee Tools.  
For replacement parts directly from Busy Bee Tools, for this machine, please call 1-800-461-BUSY (2879), and 
have your credit card and part number handy. 
 

 

All returned merchandise will be subject to a minimum charge of 15% for re-stocking and handling with the 
following qualifications. 

 

Returns must be pre-authorized by us in writing. 

 

We do not accept 

collect

 shipments. 

 

Items returned for warranty purposes must be insured and shipped pre-paid to the nearest warehouse  

 

Returns must be accompanied with a copy of your original invoice as proof of purchase. Returns must be in 
an un-used condition and shipped in their original packaging a letter explaining your reason for the return. 
Incurred shipping and handling charges are not refundable. 

 

Busy Bee will repair or replace the item at our discretion and subject to our inspection. 

 

Repaired or replaced items will be returned to you pre-paid by our choice of carriers. 

 

Busy Bee reserves the right to refuse reimbursement or repairs or replacement if a third party without our 
prior authorization has carried out repairs to the item. 

 

Repairs made by Busy Bee are warranted for 30 days on parts and labour. 

 

Any unforeseen repair charges will be reported to you for acceptance prior to making the repairs. 

 

The Busy Bee Parts & Service Departments are fully equipped to do repairs on all products purchased from us 
with the exception of some products that require the return to their authorized repair depots. A Busy Bee 
representative will provide you with the necessary information to have this done. 

 

For faster service it is advisable to contact the nearest Busy Bee location for parts availability prior to 
bringing your product in for repairs. 

CRAFTEX 3 YEARS LIMITED WARRANTY 

Summary of Contents for CX119






























Reviews: