Craftex CX119 User Manual Download Page 21

 

21

MAINTENANCE 

 

During the life of your machine, you will 
need to practice some regular maintenance 
to keep your saw in peak performance 
condition. 
 
 

REPLACING THE BLADE 

 

To replace or change the blade, turn the 
switch OFF and disconnect the cord from 
the power source. 
 
Release the blade tension lever, and 
remove the table insert and the table pin. 
To protect your hands, wear protective 
gloves. Open the upper and lower wheel 
cabinets and carefully slide the blade off the 
both wheels. Now, slide the blade out, 
through the slot on the table. 

 

TO INSTALL THE NEW BLADE: 
 

Once the old blade is removed, carefully 
slide in the new blade through the slot on 
the table so that the teeth of the blade are 
pointing downwards. Position the blade 
through the upper and lower guide bearings 
and install it over the wheels. Once the 
blade is in the proper position, turn the 
tension lever.  

Figure-29 Replacing the blade 

 

Adjust the blade tracking (See page-11) 
and adjust the guide bearings (See page-
13).  Close the top and bottom cabinets and 
insert the table pin and table insert back. 
 
 

REPLACING THE BLADE 
GUIDES 

 

The blade guides should be checked and 
adjusted every time the blade is replaced. 
The blade guides should be checked to 
ensure they turn properly and do not cause 
the blade to get stuck. 
 
Disconnect the band saw from the power 
source and turn the blade tension lever to 
release the tension on the blade. Release 
the blade guard and use a 10 mm wrench 
to loosen the bolt shown in figure-30. 

Figure-30 Bolt to be loosen 

 
Now open the two thumb screws and 
remove the thrust bearing mounting shaft 
and the blade guide mounting shaft. 
 
Remove the “C ring” and slide the thrust 
bearing off the shaft using C-ring pliers. 
Take the blade guide bearings and remove 
the “C-rings” in the same way. 
 
 

Summary of Contents for CX119






























Reviews: