CP Plus Indigo JRC-27F User Manual Download

Page: 107 / 140

101

Please refer to the following sheet for detailed information.

Parameter

Function

Enable

You need to check the box to enable motion detection function.

Please select a channel from the dropdown list.

Period

Motion detection function becomes activated in the specified periods.
See Figure 5.29.

There are six periods in one day. Please draw a circle to enable
corresponding period.

Click OK button, system goes back to motion detection interface; please
click save button to exit.

Interval

System only memorizes one event during the anti-dither period. The
value ranges from 5s to 600s.

Sensitivity

There are six levels. The sixth level has the highest sensitivity.

Record channel System auto activates motion detection channel(s) to record once an

alarm occurs. Please note you need to set motion detect record period
and go to Storage

→

Schedule to set current channel as schedule

record.

Delay

System can delay the record for specified time after alarm ended. The
value ranges from 10s to 300s.

PTZ Activation

Here you can set PTZ movement when alarm occurs. Such as go to
preset X. See Figure 5.30.

Tour

You need to check the box here to enable this function. System begins
1-wiindow or multiple-window tour display among the channel(s) you
set to record when an alarm occurs.

Show message

System can pop up a message to alarm you in the local host screen if
you enabled this function.

Send Email

If you enabled this function, System can send out an email to alert you
when an alarm occurs.

Alarm upload

System can upload the alarm signal to the server (Including alarm
server.

Buzzer

Check the box here to enable this function. The buzzer beeps when an
alarm occurs.

Summary of Contents for Indigo JRC-27F













































































































































Search results

Summary of Contents for Indigo JRC-27F

Reviews:

Related manuals for Indigo JRC-27F

Brands by name

Popular brands

CP Plus Indigo JRC-27F, User Manual

Search results

Summary of Contents for Indigo JRC-27F

Reviews:

Related manuals for Indigo JRC-27F

Brands by name

Popular brands