COX A12013G, Owner'S/Operator'S Manual, Page: 4 / 54

26 July 2013 Page 4 Cruiser Model A12013G & A16013G
PRE-DELIVERY INSTRUCTIONS
INTRODUCTION:
The purpose of this procedure is to ensure the
dealer/distributor has made the necessary
installations, adjustments and checks, before the
machine is operational. This procedure begins
upon receiving the crated mower and is finalised
once the mower has been either sold or leaves
the dealer/distributors premises. This is the
minimum amount of work required, however it
should not be limited to only the areas detailed
in this procedure.
RESPONSIBILITY:
It is the responsibility of the dealer/distributors
to ensure that before a machine is delivered to a
customer, it is in perfect operational condition.
PROCEDURE:
CHECK FOR TRANSPORT DAMAGE
UNCRATE MACHINE
CHECK ITEMS SUPPLIED IN SEAT
PROTECTION BAG

Engine owners manual

Owner/Operator manual (CD)

Tommy bar (AM007)

Ignition keys
16.0 HP Honda & B&S (AM015)
23.0 HP Honda (A120863)

Spark plug spanner (AM295)

Warranty Card

Pre-delivery Instruction Sheet

Seat Spring x 3 (13060)

Washer x 3 (W05M202)

Cup Head Bolt x 4 (M8x40)

Nyloc Nut x 4 (M8 )

Washer x 3 (W052003)

Seat Spring Cap x 3 (14128)

LH Control Lever (A12061711J)

RH Control Lever (A12061811J)
TYRE PRESSURE
Before operation ensure that all tyre pressures
are equal from side to side. The recommended
pressures are:-
Front Wheel:-140 Kpa (20psi) approximately.
Rear Wheel:- 105 Kpa (15psi) 18x8.50-8
90 Kpa (13psi) 18x9.50-8
ENGINE OIL
Before operation ensure that engine oil level is
to the full mark on the dipstick. (Read engine
owners manual for correct procedure to check &
adjust oil level).
FUEL TAP
Ensure the fuel taps at the bottom inside of the
LH & RH fuel tanks are turned to the on position
before attempting to start engine. (Use
unleaded fuel only).
Turn fuel taps off after
use.
SAFETY START SWITCHES
Drive Lever Switches - 16HP HON, 22HP &
24HP B&S
With Cutter PTO switch in DISENGAGED position
and Clutch/Park Brake Lever set in the ON
position and the Drive Levers in the DRIVE
position.
Attempt to start the engine.
Engine should not start.
Drive Lever Switches—23.0 HP Honda only
While sitting on stationary machine with Engine
running and Cutter PTO Switch in DISENGAGED
position and Clutch/Park Brake Lever set in the
ON position attempt to move the Drive Levers to
the DRIVE position.
Engine should stop.
Cutter PTO Switch -
With Drive Levers in the locked out NEUTRAL
position and Cutch/Park Brake Lever set in the
ON position, and Cutter PTO Switch in the
ENGAGED position.
Attempt to start engine. Engine should not
start.
Clutch/Park Brake Lever Switch -
With Cutter PTO Switch in DISENGAGED position
and the Drive Levers are set in the locked out
NEURAL position, and the Clutch/Park Brake
Lever in the OFF position. Attempt to start the
engine.
Engine should not start.
With Cutter PTO Switch in DISENGAGED position
and the Drive Levers in the locked out NEUTRAL
position and the Clutch/Park Brake Lever set in
the ON position.
Attempt to start the Engine.
Engine should start.
SAFETY STOP SWITCHES
Seat Switch -
While sitting on stationary machine with Engine
running ENGAGE Cutter PTO Switch. Lift weight
from Seat.
Engine should stop.
While sitting on stationary machine with Engine
running and Cutter PTO Switch in DISENGAGED
position, set the Clutch/Park Brake Lever in the
OFF position and then the Drive Levers in the
DRIVE position .
Lift weight from Seat.
Engine should stop.
Clutch/Park Brake Lever Switches -
While sitting on stationary machine with Engine
running and Cutter PTO Switch in DISENGAGED
position, and Drive Levers in DRIVE position,
attempt to set the Clutch/Park Brake Lever in the
ON position.
Engine should stop.