manualshive.com logo in svg

Courion iDRIVE, System Manual

Share
Download
Courion iDRIVE System Manual Download Page 12

12

ver.071217-2.10

iLEARN

 System Manual

COURION Logo Screen - Press the MENU/SELECT Button.

System Status Screen - System OK

NOTE

:  If this screen indicates something other than SYSTEM OK, 

please proceed to the 

TROUBLESHOOTING and ERROR MESSAGES

 

Section at the back of this Manual.

If you received an iSYSTEM Software Update Kit with your order, update the iLEARN Door 

Control and iDRIVE software by following the instructions in Courion’s iSYSTEM Software 

Update Manual.

After successfully updating the iSYSTEM Software, re-cycle the iLEARN Door Control power (110 

VAC) and iDRIVE Hoistway power (240 VAC).

3. Initial Operation

a. Insure that all of the Hoistway Doors and Car Gates are in the 

FULL CLOSE

 Position.

b. Utilizing the Hall or Car Station Push Buttons, open and close the Hoistway Doors.

To ADJUST the Hoistway Door(s) Operation (if required), press the MENU/

SELECT Button and turn to DOOR PARAMETERS.

Summary of Contents for iDRIVE

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands