Power suppy
First Mode: 13 Preset Lighting Effects
You can use the top panel’s RGB SW button to switch between the thirteen
beautiful lighting effects we have preset for you.
Second Mode: Motherboard Synchronization
Please use the included adaptor (see picture below) to connect to a
compatible motherboard’s 3-pin 5V Addressable RGB header. Then,
press and hold the RGB SW button for 3-6 seconds, the ARGB fans
at the front panel will flash in white for two consecutive times.
※
If you press and hold the RGB SW button for 3-6 seconds again, the
ARGB fans at the front panel will flash in white for two consecutive
times. It will be returned to the First mode: 13 Preset Lighting Effects.
Third Mode: Turn off RGB LED lighting effects.
Please press and hold the RGB SW button for over 6 seconds and the
ARGB fans at the front panel will flash in white for four consecutive times.
※
If you press and hold the RGB SW button for 1 seconds again, the RGB
LED lighting effects will be turned on.
RGB & Fan control system
5V Addressable
LED Connector - 1
5V Addressable
LED Connector - 4
5V Addressable
LED Connector - 5
5V Addressable
LED Connector - 6
5V Addressable
LED Connector - 2
5V Addressable
LED Connector - 3
LED Strip 1
LED Strip 2
Power Connector
RGB Button
5V Addressable Header Adapter
VDG
for Compatible
Gigabyte
Motherboards
for Compatible
Asus or MSI
Motherboards
Please don't remove the
SATA connector from the PSU.
Installing 2.5" SSDs /HDDs
2
3
3
4
1
2
5
6
2.5"
2.5"
2.5"
2.5"
1
2
Connectors
Connectors
5
5
6
Power Connector
RGB Button
RESET SW
5V Addressablle
Header Adapter
Compucase Enterprise Co.,Ltd.
No. 225, Lane 54, An Ho Road Sec. 2 Tainan, Taiwan, R.O.C
Tel:+886-6-356-0606
Service E-Mail:[email protected]
COUGAR USA Technical Service
Tel: (833) 256-3778
Mail: [email protected]
https://cougargaming.com/support/contact/upload/
For more information, please visit
Compucase Enterprise Co.,Ltd.
All rights reserved.
www.cougargaming.com
Made in China
IN
VDG
Installing
vertical graphic card
Installing the Built-in LED Controller Connectors
2
Stand-off
for VGA riser cable
The vertical graphic
card and the PCI-E
riser cable are not
i n c l u d e d i n t h e
p a c k a g e , p l e a s e
purchase separately.
3
4
1
Please choose either
of a Vertical Graphic
Card or 2.5" SSD
trays on the PSU cover
to install.
Install with trays
(There are two SSD trays in this case.
Please select two locations you prefer to install.)
1
RIGHT
RIGHT
RIGHT
RIGHT
Removing the side panels
Installing 3.5" HDDs
1
2
120
140
240
280
*360
120
140
(Top)
1
120
120
(Rear)
3
*120
*360 280 240 140 120
140
(Front)
2
Installing water cooling radiators & cooling fans
*Please choose either of front or top to install a 360mm radiator.
*Please choose either of a TOP 360mm radiator or FRONT 120mm x 3 fans to install.
1
3
2
1
2
1
2
3
4
3.5"
3.5"
3.5"
3.5"
Connectors
Connectors
1
1
2
1
2
RIGHT
3
4
LEFT
RIGHT
LEFT
