2.1 GENERAL INSTRUCTIONS
心
A. Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the outlet are
on.
B. The appliance may emit a slight, harmless odor when first used. This odor is normal and it is caused by the initial
heating of internal appliance elements and will not occur again.
C. If your appliance does not emit heat, consult the operation section of this manual for further information.
D. Use with a ETL or UL certified surge protector.
RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO
AVOIDTRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY.
DO NOT RUNCORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS, ETC.
ARRANGE CORDAWAY FROM CLUTTERED AREAS AND WHERE IT WILL NOT BE TRIPPED OVER.
公
CAUTION - Some parts of this product can become very hot and cause burns. Particular attention has
to be given where children and vulnerable people are present.
RISK OF FIRE. TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER. DO NOTUSE
ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.
RISK OF FIRE. DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.
THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED OPTIONAL ACCESSORIES.USE
OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THEWARRANTY
AND/OR RESULT IN A SAFETY HAZARD.
IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE MAY RESULTCAUSING PROPERTY
DAMAGE, PERSONAL IN」URY OR DEATH. DO NOT STORE OR USE GASOLINE OR OTHERFLAMMABLE VAPORS IN THE
VICINITY OF THIS OR ANY OTHER APPLIANCE.
THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.
HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED. AS IT MAY CREATE A FIRE
HAZARD.
Follow all National and local electrical codes.
1. The heater must not be recessed in the ceiling. There must be enough space around the top of the heater
to ensure adequate ventilation.
2. The heater should be at least 60 cm away from any surrounding walls.
3. A distance of at least 90 cm should always be left in front of the heaters to ensure safety.
4. The Heater should be mounted at a minimum of 20 cm above ground level.
5. The Heater must not be located either directly below, or in front of a socket-outlet.
6. The heater must be installed so as to prevent any control switches being able to be touched by anyone who
is in the shower or bath.
7. Make sure that there is no possibility of inflammable material, combustible material or curtains coming into
contact with the heater, there is a risk of fire if this happens.
8. DO NOT LEAVE THE HEATER UNATTENDED DURING USE.
3.1 UNPACKING AND TESTING APPLIANCE WALL
Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance
operates properly by plugging the power supply cord into a conveniently located 120 Volt grounded outlet.
GROUNDING
METIIODS
3.2 GROUNDING APPLIANCE
This appliance is for use on 120 Volts. The cord has a plug as shown in (A). An
adapter as shown in (C) is available for connecting three-blade grounding type
plugs to two-slot receptacles. The green grounding lug extending from the
adapter must be connected to a permanent ground such as a properly grounded
outlet box. The adapter should not be used if a three-slot grounded receptacle is
available.
To disconnect appliance, turn controls to off, then remove plug from outlet.
气＠
FDox
w
E
R
O
DEB
R
N
T
c
E
UE
s
勹
GRO5
曰
3
GROUNDING PIN
女
ADAP
T
ER
(:
)
GROUNDING
MEANS
NOT ALLOWED IN CANADA
A
ALWAYS unplug this fireplace heater before assembly or cleaning, or before relocating.
Failure to do so could result in electric shock, fire, or personal injury.
KEEP drapery and other furnishings at least 3ft /0.9m from the front and sides of the
electric fireplace.
AFTER installation, ensure that there is�0.004 nf ventilation area between inside and
outside of fireplace mantel.
Your new electric fireplace may be installed virtually anywhere in your home. However, when choosing allocation
ensure that the general instructions are followed. For best results, install out of direct sunlight. Power supply
service must be either completed or placed within the electric fireplace prior to finishing to avoid reconstruction.
When moving the insert into mantel, Do not let bottom of insert touch the mantel to avoid the scratch.
个
10
11
