manualshive.com logo in svg

Costar Video Systems CRIS12, Operation Manual

Share
Download
Costar Video Systems CRIS12 Operation Manual Download Page 11

11

Part 1 - Introduction

LED Status Indications

Mode

Status

Color

Description

LNK/ACT

(Link/Activity)

On

Amber

Normal network connection at 10/100Mbps

Green

Normal network connection at 1000Mbps

Blinking

Amber

Data transmission over the network in progress at 
10/100Mbps

Green

Data transmission over the network in progress at 1000Mbps

Off

-

No network connection or a problem with the connection

PoE

(while PoE 

LED button is 

pressed)

On

Amber

Connected to an IEEE 802.3af powered device

Green

Connected to an IEEE 802.3at powered device

Off

-

Not connected to a powered device

3

  RJ-45 Uplink Ports

RJ-45 uplink ports are used to connect the switch to a higher tier device. These ports are 
useful when cascading multiple network devices.

Model

Port Number

CRIS12

9 (top) and 10 (bottom) 

CRIS28

25 (left) and 26 (right)

•  If not using for uplinking purposes, these ports can be used as service ports, but they do not 

support PoE.

•  The ports operate in different modes based on the network speed. (10/100Mbps: full/half 

duplex, 1000Mbps: full duplex)

Summary of Contents for CRIS12

























Reviews:

No comments

Brands by name

Popular brands

Load more brands