Cortelco WPBX00 PRO MAN Programming Instructions Manual Download Page 28

Page: 28 / 28

WPBX00 PRO MAN

NO ANSWER GREETING

5.4

If No Answer Timeout is enabled, then the No Answer greeting will be played. After the

timeout (value) time, then the system will repeat the previous day or night mode voice prompt.

NO DIGIT TIMEOUT

5.5

If no digit timeout is enabled, then if the caller does not enter DTMF digits within the

designated time frame, the call will be forwarded to the appropriate extension. A timeout value

must be entered and an extension for forwarding calls after enabling the feature.

CONSOLE AND AUTO ATTENDANT MODE

5.6

Under Setup - Settings - Operator, the current operator mode is shown. When the Opera-

tor mode is selected, all incoming calls to PSTN lines will be routed to the console phone (default

is extension 0, SLT port 6). When the system is in No Operator mode, the system then uses auto

attendant as the operator. The auto attendant voice prompt will be played.

PERMANANT AUTO ATTENDANT MODE

5.7

Change all auto changes under Operator to NO and click on NO OPERATOR, then

press Update. The system will now be in permanant auto attendant mode

Summary of Contents for WPBX00 PRO MAN





























Search results

Summary of Contents for WPBX00 PRO MAN

Reviews:

Related manuals for WPBX00 PRO MAN

Brands by name

Popular brands

Cortelco WPBX00 PRO MAN, Programming Instructions Manual

Search results

Summary of Contents for WPBX00 PRO MAN

Reviews:

Related manuals for WPBX00 PRO MAN

Brands by name

Popular brands