background image

WPBX00 PRO MAN

Cortelco

COMPASS  Wireless  PBX  System

PROGRAMMING  INSTRUCTIONS

CONTENTS                                           PAGE

1.    INTRODUCTION ................................. 1

2.    PROGRAMMING INFORMATION ....... 1

COMPUTER REQIUREMENTS ....... 1

PRINTER REQUIREMENTS............. 1

TECHNICAIN PASSWORDS ........... 1

GENERAL RULE ............................. 2

3.    SOFTWARE INSTALLATION .............. 2

4.    PROGRAMMING ................................ 3

PBX CONFIG ................................... 4

EXT. SETUP .................................... 5

CLASS OF SERVICE ...................... 8

HANDSET DEREGISTRATION ........ 8

SYSTEM STATUS ............................ 9

CALL LOG ..................................... 10

CALL LOG SETUP ........................ 12

NUMBER PLAN ............................. 13

PRINTER AND PAGE SETUP........ 14

FAX AND MODEM ......................... 14

DISTRIBUTOR MODE .................... 15

SETTINGS ..................................... 16

EMERGENCY NUMBERS ............. 18

MBS SETTINGS ............................ 19

CLASS OF SERV. SETTINGS ....... 23

RBS CABLE LENGTH ................... 24

DIAGNOSTICS............................... 25

CLEAR SETTINGS ........................ 25

5.  AUTO ATTENDANT............................ 27

Page 1

1.

INTRODUCTION

1.01 This section describes programming

for  the  Compass  Wireless  PBX  System

equipped with Programming Software.  In-

structions are included for completing the nec-

essary programming.

1.02 Whenever this section is reissued, the

reason for reissue will be listed in this para-

graph.

RELATED DOCUMENTS

1.03 For additional information regarding

the Compass Wireless PBX System, refer to

the General Description and Installation manu-

als.

2.

PROGRAMMING INFORMATION

2.01 The  following  paragraphs  provide

guidelines to assist the technician during sys-

tem database planning and programming.

COMPUTER REQUIREMENTS

2.02 Pentium  133  or  above  with  RS232

Com port, Windows 98, 2000, XP or ME.

PRINTER REQUIREMENTS

2.03 Epson dot matrix printer or compatible.

TECHNICIAN PASSWORD

2.04 Access to programs in the customer

database is protected by several passwords.

The  passwords  are  listed  on  the  following

page.

Summary of Contents for WPBX00 PRO MAN





























Reviews: