background image

CORSIVA  YACHTING 

 

 

28 

 

16. MAINTENANCE, PAINTING, CLEANING 

Your boat – the deck, hull and some interior parts were made of fiberglass. 
To keep the boat in good condition, wash the fiberglass regularly.  Wash the boat with clean 
water with soft detergents, e.g. water with soap. 
 
Do  not  use  abrasive  cleaning,  solvents,  ammonia,  chlorine  or  acetone  as  these  will  damage 
the gel-coat surface. 
 
In extreme cases, special cleaners may be used to remove sea growth or algae from the hull. 
Growths and algae can worsen the efficiency of the boat. 
Do  not  use  wire  brushes,  abrasive  paper  or  paste  to  remove  growths  and  algae.  The  arisen 
scratches may store dirt, growth and algae. 
The hull bottom should be painted with anti-fouling. 
 
Before painting the boat, please consult with the manufacturer which paint is the best

 

 

 

 
 
 

 
 
 
 

 

 

WARNING 

Cleaning  or  washing  with  solvents  can  cause  the  fire,  explosion  and  health 
problems.  Always  wear  necessary  protective  clothing  while  cleaning  (gloves, 
goggles, protective mask). 

CAUTION 

Get acquainted with safety code of environment protection before painting the 
boat. Get acquainted with suggestions and instructions of using products before 
you  start  using  them.  Follow  the  instructions  of  the  paints’  and  varnishes’ 
manufacturer.  Consult  the  local  authorities  to  learn  the  current  regulations 
concerning environmental protection. 

UWAGA 

To  maintain  the  warranty  on  the  hull  of  the  boat  should  be  serviced  every  year 
and the hull to protect antyfouling.

 

Summary of Contents for 475 New Age 2015







































Reviews: