manualshive.com logo in svg

Coretec VCX-4400-E, Installation And Operating Instructions Manual

Share
Download
Coretec VCX-4400-E Installation And Operating Instructions Manual Download Page 8

com1ip 192.168.5.151 (IP address of the decoder that is sending sub-channel commands) 
com1tcp 1 (assume a universal decoder) 
com1server 0 
com1timeout 10 
com1baud 38400 

 

MPEG4 Configuration 

The MPEG4 encoder requires the following parameters be configured to your network: 

 
videoip 239.5.5.151 (use a valid IP on your network) 
port 4570 
bitrate 1000 
res cif 
fps 15 

 
Saving Configuration 

When all the configuration parameters have been entered, they must be saved to memory and the unit 
restarted by entering the following command: 
 

Commit

 

<enter>   (please wait a moment until the following prompt appears:) 

 

 

 

COMMIT

 

 

 

DONE

 

 

 

 

 

Reboot

 

<enter>

 

 

 

 

 
 
 
 

Updating

 

Firmware

 

with

 

VCXNetBurner

 

 

Introduction  

 
VcxNetburner is a Windows 2000/XP application that allows updating of the VCX-2400  
Encoder/Decoder firmware (as well as the VCX4400E and VCX6400E.) VcxNetBurner can 
simultaneously the firmware of all VCX-2400 devices that can be accessed on your network. If 
you can telnet to the device then VcxNetBurner can update the firmware. The only exception is 
that the device’s current firmware version must be v1.5 or higher. Firmware v1.4 does not 
contain the update feature.  

Summary of Contents for VCX-4400-E







































Reviews:

No comments

Brands by name

Popular brands

Load more brands