manualshive.com logo in svg

Coretec VCX-4400-E, Installation And Operating Instructions Manual

Share
Download
Coretec VCX-4400-E Installation And Operating Instructions Manual Download Page 3

 

Introduction 

 

The VCX-4400-E and the -ER are the chassis versions of the Core Tec stand-alone VCX-

4400 MPEG-4 IP product series.  These units are fully compatible with the “-ER” card cage 
versions of the product series.   

The VCX-4400 Digital Video Codec system consists of a video encoder and a Core Tec 

decoder pair providing the capability for one-way end-end transmission of compressed digital 
video in IP packets at data rates in the 64kbps to 3.5 Mbps range. 
 

The system employs MPEG-4 encoding.  The encoding-decoding process is applied to an 

NTSC (or PAL) video input, selected in software.     
 

The video encoder converts the video to a serial signal, which is multiplexed with any 

data sub-channels present.  The stream is then formatted into a series of IP packets sent to the 
network through a standard Ethernet connection. 
 

Modification to video format and resolution, data sub-channel characteristics, and basic 

IP parameters are achieved through one of the following means: 
 

a)

 

a Hyper Terminal accessible menu 

b)

 

Telnet through the Ethernet connection 

c)

 

Watchdog CCS 

 

The video decoder receives the IP packets, separates the video data from the data sub-

channels, and converts the video data to analog form, providing an NTSC (or PAL) output. 
 

The units feature two bi-directional data sub-channels (programmable for RS-232 or RS-

422). Data bits are multiplexed with the digital data stream.  

 

 

Summary of Contents for VCX-4400-E







































Reviews:

No comments

Brands by name

Popular brands

Load more brands