manualshive.com logo in svg

Coretec VCX-4400-E, Installation And Operating Instructions Manual

Share
Download
Coretec VCX-4400-E Installation And Operating Instructions Manual Download Page 22

 

2)

 

Terminal Program 

 

NOTE

: The following procedure is valid for standalone units only and is not applicable to 

rack mount units. 

 

The Terminal Program, such as HyperTerminal, configuration procedure uses the serial 
connection on the front of the unit. 

 

Using the PCA-2400 programming cable, connect to the control port. This cable should be 
attached to the serial port of an attached PC and the Hyper Terminal program launched. The 
PC should have its Com Port configured as: 

 
Baud rate 

38,400 kbps 

Data bits 

8 bits 

Parity  

No Parity 

Stop Bits 

1 Stop Bit 

Flow control  None 
 

Activate the HyperTerminal function, normally found in a sub-menu under ACCESSORIES. 
Employ the command set as described in the following section. 

 
Password: admin (default) 
 

To change the default password perform the following: 
 
Type: 

PASSWORD

 <followed by your password (up to 11 characters)> 

 
Where <your password> equals the new password 

 

3)

 

Core Tec Watchdog Lite Software 

 

Please refer to the Watchdog Manuals. 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for VCX-4400-E







































Reviews:

No comments

Brands by name

Popular brands

Load more brands