manualshive.com logo in svg

CopyPro CD-R 3500, User Manual

Share
Download
CopyPro CD-R 3500 User Manual Download Page 22

CopyPro CD-R 3500                                                 Trouble Shooting

 

 

 

 

 

CopyPro

 

CD-R 3500

  

 

19

 

Trouble Shooting 

Please refer to the table below in the case of following start up messages: 

 
 

Boot Error Message 

Description 

 
HDD Not Detected 

 
Problem in accessing HDD inside CD-R 3500XL 

Unable To Access HDD 

Problem in accessing HDD inside CD-R 3500XL 

Loading SCSI Driver 

Error occurred while loading ASPI device driver into memory 

Unsupported CDR 

Trying to connect an unsupported CD-Writer.  Only Yamaha and Teac 
CD-Writers are supported in this version. 

HDD Capacity Less 

HDD of 650 MB capacity is required.  If smaller capacity HDD is 
connected, this warning message is displayed indicating that larger 
capacity CDs may not be duplicated. 

No CDR Found 

Problem in accessing CDRs in 3500. 

Memory Not Detected 

Problem in accessing DRAM in the Controller Card of 3500. 

Memory Insufficient 

Problem in accessing DRAM in the Controller Card of 3500. 

 
 

For technical support, please call

    

 

CopyPro, Inc.

   

 

1-800-887-9906

 

 

Summary of Contents for CD-R 3500























Reviews:

No comments

Brands by name

Popular brands

Load more brands