background image

 
 

 

Petrol Brush Cutter 

10596

 

Instructions for Use 

Please read and retain these instructions for future reference

 

v001: 18/10/16 

 

Page No. 4 

 

 

(a)

 

The port to refuel the “MIX GASOLINE” 
Position: FUEL: TANK CAP 
 
 

(b)

 

The direction to close the choke 
Position: AIR CLEANER COVER 
 
 

(c)

 

The direction to open the choke 
Position: AIR CLEANER COVER 

 

 

 

 

4.

 

SAFETY PRECAUTIONS 

 

BEFORE USING THE MACHINE 
a.  Read this owner’s manual carefully to understand how to operate this unit properly. 
b.  This product has been designed for use in cutting grass, and it should never be used for any other 

purpose. 

c.  You should never use this brush cutter when under the influence of alcohol, when suffering from 

exhaustion or lack of sleep when suffering from drowsiness as a result of having taken cold 
medicine, or any other time when a possibility exists that your judgement might be impaired or 
that you might not be able to operate the brush cutter properly and in a safe manner. 

d.  Avoid running the engine indoors. The exhaust gases contain harmful carbon monoxide. 
e.  Never use your brush cutter under circumstances like those described below: 
       When the ground is slippery and when other conditions exist which might make it not possible to 

maintain a steady stance while using the brush cutter. 

       At night, at times of heavy fog, or at any other times when your field of vision might be limited 

and it would be difficult to gain a clear view of the area. 

       During rain storms, lightning storms, at times of strong or gale-force winds, or any other time 

when weather conditions might make it unsafe to use this product. 

f.  Lack of sleep, tiredness or physical exhaustion results in shorter attention spans, and this in turn 

can lead to accidents and injury. Limit the amount of time the brush cutter is to be used 
continuously to approximately 30-40 minutes per session, and  take 10-20 minutes of rest 
between sessions. Also try to keep the total amount of work performed in a single day under 2 
hours or less. 

g.  Be sure to keep this manual handy so that you may refer to it later whenever any questions arise. 
h.  Always be sure to include this manual when selling, lending or otherwise transferring the 

ownership of this product. 

i.  Never allow children or anyone unable to fully understand the directions given in this manual to 

use this brush cutter. 

 

WORKING GEAR AND CLOTHING 

 

Summary of Contents for 10596

















Reviews: