manualshive.com logo in svg

Coopers 10596, Instructions For Use Manual

Share
Download
Coopers 10596 Instructions For Use Manual Download Page 10

 
 

 

Petrol Brush Cutter 

10596

 

Instructions for Use 

Please read and retain these instructions for future reference

 

v001: 18/10/16 

 

Page No. 10 

INSTALLING THE METAL BLADE (F6) 

1.

 

Set the inner holder to the gear shaft and turn it so that 
the hole is aligned with the hole in the gear shaft, put 
the hex key in this hole to fixate for assembling the nut. 

2.

 

Put the blade on the inner holder with the face with 
letters to the gear case, and match the hole of the 
blade to the projection of the inner holder correctly. 

3.

 

Set the outer holder to the gear shaft with the 
hollowed face to the blade. 

4.

 

Put the attached metal cover on the outer holder and 
secure it with the nut. 

5.

 

Remove hex key. 
(1) Wrench 
(2) Nut 
(3) Top metal cover 
(4) Outer holder 
(5) Blade 
(6) Inner holder 
(7) Gear shaft 
(8) Hex key 
(9) Gear case 

 

 

INSTALLING THE NYLON CUTTER (F7) 

 

1.

 

Set correctly the inner holder to the gear shaft only (see F6). 

2.

 

Screw the attached bolt (M10 left) into the gear shaft and 
secure it with the spanner. 

3.

 

Screw the nylon cutter into the bolt by fixing the inner holder 
with the L-shaped bar and tighten it manually. 

NOTE 
Keep bolts and washers to install the blade carefully so as not to 
lose them 
(1) Gear case 
(2) Bolt 
(3) Nylon cutter 
(4) Nylon cord 
 

 

6.

 

FUEL 

WARNING.  

 

Gasoline is very flammable. Avoid smoking or bringing any flame or sparks 
near fuel. 

 

Wipe up all spills before starting the engine. 

 

Make sure to stop the engine and allow it to cool before refuelling the unit. 

 

Keep open flames away from the area where fuel is handled or stored. 

 

 

IMPORTANT 

 

Summary of Contents for 10596

















Reviews:

No comments

Brands by name

Popular brands

Load more brands