5
Directions for use
Prior to the first use, especially if outdoor temperature is below zero, let the
device heat up at room temperature for 1 hour. It is recommended to use
the device at temperature ranging from 5°C to 40°C, and relative humidity
not more than 80%. Use only clean water with temperature not more than
30°C. Prior to a switching the device off for a long time (more than 2 days),
drain water from the tray and dry the discs block. Read instructions how
to clean the discs block and the tray in section «Recommendations on
maintenance of the device».
CONTROL OF THE DEVICE
•
POWER on/off button (16).
Press the «POWER» button (16) to switch the device on. Pressing this button
again will stop the device and switch it to the standby mode.
•
«SPEED» performance mode selection button (9).
Press the «SPEED» button (9) to select the performance mode. There are
three main operation modes: LOW (minimal performance), MID (average
performance) and HIGH (maximum performance), as well as the additional
automatic mode «AUTO» (6) (see page 5 for description of the mode
operation. When selecting a mode an indicator (10) will light up on the panel.
•
«ANION» ionization activation button (7).
Press this button to activate the negative ion generator, the ionization
indicator (3) will light up on the control panel.
•
«SLEEP» night mode button (8).
Press the «SLEEP» button (8) to switch the device to the night mode (see
page 4 for description of the mode operation).
5. POWER on/off button (16).
•
«TIMER» button (13).
By pressing the «TIMER» button (13) you can set a time interval to switch
the device off ranging from 1 to 8 hours with a 1-hour increment. At that, the
selected time (12) will be displayed on the control panel.
•
«LIGHT» lighting button (14).
By pressing the «LIGHT» button (14) you can activate or deactivate the
lighting function.
Lock button to prevent accidental pressing of buttons and ensure
childproofing «TIMER» + «LIGHT» (15).
Press and simultaneously hold «TIMER» and «LIGHT» buttons (15) for about
3 seconds to lock / unlock control buttons to avoid accidental (erroneous)
pressing of buttons. When activating this function, the button lock indicator
(11) will be displayed.
1. Air washer – 1 pc.
2. Operation manual – 1 pc.
3. Packing – 1 pc.
4. Bio Silver Stone filter – 1 pc.
5. SCOPE OF DELIVERY
6. FILLING OF TANK WITH WATER
To pour water into the tray, take the device case handles, remove it by lifting
upwards and move aside. Take the tray by handles with both hands (with
a drum or without it), fill in water up to the mark. To avoid accidental falling
or hitting, hold it with both hands. Move the filled tray to the supposed
location of operation. Install the device case on the tray filled in with water
so that the drum wheel coincides with the device gear.
7. OPERATION OF THE UNIT
Please note that trailers in the tray are located on the front side. Connect
the device to the electric mains, press the «POWER» button, use buttons
on the control panel to select the desired operation mode and time.
You can find accurate description of the meanings of buttons in section
«Control of the device». To switch the device off, press the «POWER»
button. Disconnect the device from the electric mains. Please note that
trailers in the tray are located on the front side.
•
Current humidity level indicator (4).
Readings of the current humidity indicator may vary dynamically.
Approximate relation of readings: «LOW» – low humidity level, «MID» –
average, «HIGH» – high.
•
Low water level indicator (5).
When water level in the tray lowers to minimum, the low water level indicator
(5) will light up. Along with that, several sound signals will be heard, notifying
of water shortage, after that the device will be switched off.
www.cooperandhunter.com
