background image

1

Types VXE15 and VXE27
Electronically Controlled Single-Phase;
Installation and Operation Instructions

Reclosers

Service Information

S280-16-1

Printed in USA

November 2002 • Supersedes 8/01

Figure 1.
Kyle

®

Type VXE electronically controlled, single-phase, vacuum-interrupting automatic circuit recloser. 

020100KM

VXE15 Serial Number 11009 and above
VXE27 Serial Number 1948 and above

VXE Control Serial Number 7401 and above

Safety Information 

......................................................

2

Safety Instructions  ....................................................

2

Hazard Statement Definitions ...................................

2

Product Information 

....................................................

3

Introduction ...............................................................

3

Acceptance and Initial Inspection .............................

3

Handling and Storage ...............................................

3

Description ................................................................

3

Manual Operating Levers and Indicators  .................

5

Recloser Data Plates ................................................

6

Control Programming and Operation 

.......................

7

Type VXE Electronic Control  ....................................

7

Programming the Control Settings  ...........................

8

Specifications and Ratings 

......................................

10

Dimensions 

................................................................

11

Installation Procedure 

..............................................

12

Placing the Recloser In Service  .............................

13

Operation 

...................................................................

14

Manual Operation of Energized Recloser  ..............

14

Non-Reclosing Operation  .......................................

14

Automatic Operation ...............................................

14

Lockout Indication ...................................................

14

Testing 

.......................................................................

15

Safety Requirements  ..............................................

15

Test Equipment Required  .......................................

15

Manual Closing Procedure  .....................................

16

High-Potential Insulation Withstand Tests  ..............

16

Minimum-Trip Current Level Test  ...........................

17

Sequence of Operation Test  ...................................

17

Electrical Operation of Closing Solenoid Test  ........

18

Accessories 

...............................................................

19

Extra Creepage Bushings  ......................................

19

Bushing-Type Multi-Ratio Current Transformer ......

19

Low-Voltage Closing ...............................................

19

Cable-Locking Sleeve .............................................

19

SCADA Input/Output Board  ....................................

19

Maintenance Information 

.........................................

20

Contents

NOTICE: This bulletin is also applicable to Kyle product
serial numbers beginning with the prefix CP57.

Summary of Contents for VXE Control





















Reviews: