P83611 J
Sheet 4 of 4
EXISTING FSB
BOX
RETROFIT PLATE MOUNTING
E
12
12
12
12
AWG #18 AWG #16 AWG #14 AWG #12
MAXIMUM NUMBER OF CONDUCTORS
SCREW COVERS
#8-32 SCREWS
RETROFIT
PLATE
DBB OR 4" SQ. X 2-1/8"
DEEP BACKBOX
ISP EXTENDER
SURFACE OR SEMI-FLUSH (4" X 2-1/8" BOX)
F
12
8
10
12
AWG #18 AWG #16 AWG #14 AWG #12
MAXIMUM NUMBER OF CONDUCTORS
SCREW COVERS
#8-32 SCREWS
SURFACE OR SEMI-FLUSH (4" X 1-1/2" BOX)
G
#8-32 SCREWS
SCREW COVERS
MAXIMUM NUMBER OF CONDUCTORS
AWG #18 AWG #16 AWG #14 AWG #12
8
8
4
10
ISP EXTENDER
DEEP BACKBOX
DBB OR 4" SQ. X 2-1/8"
AMT Appliances can be wall or ceiling mounted.
MOUNTING PROCEDURES:
CAUTION:
If sheated multiconductor cable or 3/4" conduit fittings are used, check that installed product has sufficient clearance and wiring room prior to
installing backboxes and conduit.
1. AMT Multitone Appliances can be flush mounted to a standard 4 inch square by 2-1/8 inch deep electrical box (Figure A) or a standard 2-gang by 2-1/2
inch minimum deep electrical box (Figure B).
2. Select largest backbox shown in Mounting Options where possible, to provide additional wiring room for easy installation.
3. Conduit entrance to backboxes should be selected to insure sufficient wiring clearance for installed equipment. When extension rings are required, conduit
should enter through backbox, not extension ring. Use Steel City #53151/1-1/2" deep or #53171/2-1/8" deep extension rings or equal with same area cut
out in back.
4. The AMT-12/24 model can also be surface mounted to Cooper Notification's Indoor/Outdoor Backbox (Model IOB) for indoor/outdoor use (Figure C).
5. The AMT-12/24 model is supplied with four snap-in covers to hide the mounting holes and provide an attractive installation. The snap-in covers are
interchangeable and have slots on each end so they can be removed if necessary (by prying them up with a thin blade screwdriver). To insert snap-in cover,
slide one side partially into mounting hole recess; align the cover so that snap-in cover and grille are parallel to each other (not tilted) and snap cover into
place.
6. The IOB surface backbox has 1/2 inch conduit knockouts on two sides. It has a variety of knockouts on the back for mounting it to recessed electrical
boxes and for wire entrances (Figure D). It can also be mounted to a surface with the two mounting ears that are supplied. The ears slide into slots on the
back of the box. Use appropriate anchors for the wood screws that are supplied with the box (if necessary).
7.
For outdoor use, the IOB includes a prefastened gasket and four hole plugs. Use the mounting ears to secure the box (do not use the back knockouts). Use
the hole plugs to seal the unused mounting holes on the AMT Multitone grille (press them in securely from the back side of the grille). Mount the unit to
the IOB with the four #8-18 screws supplied with the box.
8.
All models are UL Listed for indoor and outdoor use with a temperature range of -40
o
F to +150
o
F (-40
o
C to +66
o
C) and maximum humidity of 98%,
2% RH.
WARNING: IF AMT MULTITONE APPLIANCES ARE OPERATED WITHIN 15 INCHES OF A PERSON'S EAR, THEY CAN PRODUCE A
SOUND PRESSURE LEVEL THAT EXCEEDS THE MAXIMUM 120 dBA PERMITTED BY ADA AND OSHA RULES. EXPOSURE TO SUCH
SOUND LEVELS CAN RESULT IN DAMAGE TO A PERSON'S HEARING.
The AMT Multitone products and these instructions are copyrighted by Cooper Notification and contain proprietary, confidential and trade secrets of Cooper
Notification. No part of the AMT Multitone products and these instructions may be photocopied, printed or reproduced in any form or modi fied, adapted,
changed or enhanced, or converted to another programming language, or used to create updated, related or derivative works, without the prior written consent of
Cooper Notification. No part of the AMT Multitone shall be decompiled, disassembled or reverse engineered.
ANY MATERIAL EXTRAPOLATED FROM THIS DOCUMENT OR FROM COOPER NOTIFICATION MANUALS OR OTHER DOCUMENTS
DESCRIBING THE PRODUCT FOR USE IN PROMOTIONAL OR ADVERTISING CLAIMS, OR FOR ANY OTHER USE, INCLUDING
DESCRIPTION OF THE PRODUCT'S APPLICATION, OPERATION, INSTALLATION AND TESTING IS USED AT THE SOLE RISK OF THE
USER AND COOPER NOTIFICATION WILL NOT HAVE ANY LIABILITY FOR SUCH USE.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1)
Reorient or relocate the receiving antenna, 2) Increase the separation between the equipment and receiver, 3) Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected, and 4) Consult the dealer or an experienced radio/TV technician for help.
01/16
