background image

The manufacture of this product will not be held responsible if someone is injured or
the unit is damaged,    as a result of   improper installation, debugging,  unnecessary 
maintenance which is not in line with this manual. 

This manual  includes all the necessary information about  installation, debugging,  
discharging and maintenance. Please read this manual carefully before you open or 
maintain the unit. 

4   Quiet running
     High quality and efficient compressor, fan and water pump is used to ensure the low 
     noise level with insulation.
5   Good heat exchange rate
     The heat pump unit use special designed heat exchanger to enhance whole efficiency.

 

   

The unit must be installed by qualified personnel.

The unit can only be opened or repaired by qualified installer or an authorised dealer.

Use genuine standard spare parts only.

Maintenance and operation must be carried out according to the recommended time and

    frequency, as stated in this manual.

   Failure to comply with these recommendations will invalidate the  warranty.

2   Nice appearance
     The heat pump is designed with beautiful looking. The monobloc one has the water
     pump included which is very easy for installation. 

3   Flexible installation 
     The unit has smart structure with compact body, just simple outdoor installation is needed.

 This series of heat pump unit owns following features:

1   Advanced controlling
     The PC microcomputer based controller is available for the users to review or set the 
     running parameters of the heat pump.  Centralized controlling system can control several
     units by  PC.

   It is vital that the below instructions are adhered to at all times to keep the warranty.

Inverter ir ource  ater eat ump

a

s

w

h

p

 is a kind of high efficiency, energy saving and 

environment friendly equipment,  which is mainly used for house warming. It can work with
any kind of indoor unit such fan coil, radiator, or floor heating pipe, by provide warm or hot 
water. One unit of monobloc heat pump can also work with several indoor units. 
The air source water heat pump unit is designed to have heat recovery by using super 
heater which can provide hot water for sanitary purpose.
 

6   Large working range
     This series of heat pump is designed to work under different working conditions as low
     as -15 degrees for heating. 

In order to provide the customers with high quality, strong reliability and good versatility 
product, this heat pump is produced by strict design and manufacture standards.  

  

Preface

1

Summary of Contents for CH-HP08UIMPRK





































Reviews: