Cooper & Hunter Arctic NG Wi-Fi Series, Owner'S Manual

Page: 22 / 111

22
Child lock function
Press "▲" and "▼" simultaneously to turn on or
turn off child lock function. When child lock func
-
tion is on, " " icon is displayed on remote control
-
ler. If you operate the remote controller, the " "
icon will blink three times without sending signal to
the unit.
Under OFF status, press "▼" and "MODE" buttons
simultaneously to switch temperature display
between °C and °F.
Temperature display switchover function
Interface of dry contact device is provided, while
the dry contact device shall be prepared and in-
stalled by the customer.
Dry Contact function
Press uninterruptedly
"LIGHT"
button 6 times in 5
seconds thus we enter the
"
Multi Timer
"
mode as well
as three-minute-counting-down stars. If three couples
of times commands are valid and well-received in
3 minutes, the
"
Multi Timer
"
will be activated along
with the success sound of four buzzing, and the for-
mer
"
Multi Timer
"
settings with be replaced. If not,
then
"
Multi Timer
"
mode exits along with the failure
sound of six buzzing, and the former
"
Multi Timer
"
settings still remain effective.
Multi timer function
● THREE TIMERS
Outdoor temperature display is not available for some
models. At that time, indoor unit receives " " sign-
al, while it displays indoor set temperature.
It's defaulted to display set temperature when turning
on the unit. There is no display in the remote control
-
ler.
Only for the models whose indoor unit has dual-8 dis-
play.
When selecting displaying of indoor or outdoor ambi
-
ent temperature, indoor temperature indicator dis-
plays corresponding temperature and automatically
turn to display set temperature after three or five se-
conds.
●
●
●
●
NOTE
Under heat mode, press "TEMP" and "CLOCK" but-
tons simultaneously to start up or turn off 8°C heat-
ing function. When this function is started up, " "
and "8°C" will be shown on remote controller, and
the air conditioner keep the heating status at 8°C.
Press "TEMP" and "CLOCK" buttons simultane
-
ously again to exit 8°C heating function.
Under energy-saving function, fan speed is defaulted
at auto speed and it can't be adjusted.
Under energy-saving function, set temperature can't
be adjusted. Press "TURBO" button and the remote
controller won't send signal.
Sleep function and energy-saving function can't oper
-
ate at the same time. If energy-saving function has
been set under cool mode, press sleep button will
cancel energy-saving function. If sleep function has
been set under cool mode, start up the energy-saving
function will cancel sleep function.
●
●
●
Under cooling mode, press "TEMP" and "CLOCK"
buttons simultaneously to start up or turn off ener -
gy-saving function. When energy-saving function
is started up, "SE" will be shown on remote con -
troller, and air conditioner will adjust the set tem -
perature automatically according to ex-factory
setting to reach to the best energy-saving effect.
Press "TEMP" and "CLOCK" buttons simultane -
ously again to exit energy-saving function.
Energy-saving function
NOTE
Function introduction for
combination buttons
8°C heating function
Under 8°C heating function, fan speed is defaulted at
auto speed and it can't be adjusted.
Under 8°C heating function, set temperature can't be ad-
justed. Press "TURBO" button and the remote con-
troller won't send signal.
Sleep function and 8°C heating function can't operate
at the same time. If 8°C heating function has been set
under heat mode, press sleep button will cancel 8°C
heating function. If sleep function has been set under
heat mode, start up the 8°C heating function will cancel
sleep function.
Under °F temperature display, the remote controller will
display 46°F heating. ●
●
●
●
NOTE