COOLSTUFF Ocean Xplorer, Manual

Page: 4 / 36

EN
CAUTION
• Allow the battery to fully charge before the first use.
• The battery can be charged directly in the scooter,
make sure to turn OFF the power switch.
• The Battery Housing should always be ventilated
during charging to allow potentially explosive gases
to dissipate. Before removing/attaching any battery
cables always allow two minutes for any gases to
dissipate.
• ALWAYS plug the charger jack into the charging
socket first and then plug into the mains (220V AC).
• When charging is complete, unplug the charger from
the mains first and then from the charging socket.
• ALWAYS ensure the charger is DRY before plugging
it into a live socket.
• NEVER place the battery in a sealed container when
charging.
• Never charge battery near water.
• If in doubt of the state of the battery, recharge it until
the indicator on the battery charger flashes indica-
ting a full charge.
• ALWAYS charge battery in a well-ventilated place,
not in direct sunlight, and keep it out of reach for
children.
• ALWAYS ensure the unit is dried thoroughly before
opening the Nose Cone for charging or changing the
battery.
CAUTION
• ALWAYS charge the battery fully to ensure long bat-
tery life. Charging time: 6-7 hours.
• NEVER charge the battery for more than 12 hours,
as it may damage, deform or overheat the battery.
• Only use the dedicated charger for the scooter.
• The red light shown when charging indicates that the
power has been connected.
• For periods of prolonged non-use recharge battery
periodically to keep it fully charged and ensure long
battery life.
BATTERY USE
BATTERY CARE
• The battery should be recharged as soon as possible
after use.
• If the unit is not used for extended periods, the battery
should be removed from the unit and charged overnight
every three months.
• Only use the charger supplied with the scooter.
• Never place the battery in a sealed container when char-
ging.
• Never short circuit the battery or battery cable.
• Never place/store the battery near a radiator/fire, etc.
• To store the battery, remove it from the scooter or se-
parate it
• from the charger, insulate the battery terminals and keep
in a place that is dry and cool.
BATTERY USE
Charging the battery
1. Always ensure that the Master Switch is OFF.
2. Always ensure that the scooter is out of the water and
placed in a dry area (image 1).
3. Give a half turn (180°) to the Latches and remove them
from the Nose Cone as shown in image 2 .
4. Remove the Outer Nose Cone and Buoyancy Control
Chamber (image 3).
5. Open the Vent by unscrewing the Vent Plug (image 4).
6. Remove the Inner Nose Cone. To do this, first feed the
silicone ring through the latch holes in the Inner Nose
Cone and hook over the hooks on the Battery Housing
(see image 5). Then screw the Pump Nozzle onto the
Vent Hole and pump air into the Battery Chamber until
the Inner Nose Cone pops off and then remove the sili-
cone ring.
7. Allow two minutes for any gases to dissipate.
8. When you charge the sea scooter for the very first time,
this battery wire is not connect, make sure you do the-
right connect as shown in image 6. Notice: Black color-
wire is negative electrode, Red wire is positive electro-
de, make sure to match black wire with black side, and
red with red side.
9. After you connect the battery wire, make sure put the
battery wire back as image 7 shows.
10. Connect the battery cable to the charger cable and plug
charger into mains. Do not replace the Nose Cone.
11. Charging will take 6 to 10 hours for a fully discharged
battery. Unplug the adapter from the mains when fully
charged.
12. Unplug the battery cable from the charger cable and re-
connect to the housing cable.
13. Make sure the seals and sealing surfaces are clean and
lubricated before replacing the Inner Nose Cone (see
image 8). Don’t rub off the oil as this waterproofs the
unit.
14. Replace the Inner Nose Cone and make sure it is alig-
ned correctly. See image 9.
15. Replace the plastic cover of the Vent O Ring, use some
force to press it down and make sure the lid is in right
place. Make sure that the inside air can come out from
the Vent Hole when you press hard on it.
16. Screw in the Vent Plug to seal the vent (image 10).
17. Replace the Buoyancy Control Chamber.
18. Replace the Outer Nose Cone, make sure to align it cor-
rectly (image 11).
19. Insert the Latches and press them firmly in place, and
then lock the Nose Cone by giving them a half turn. See
image 12. The Latches are marked L for left side and R
for right side.
Note: To charge a battery outside of the unit, simply connect
to the charger, then plug the charging adapter into the ma-
ins. When the battery is charged, unplug the adapter first
then the battery.