Coolmay CX-WIFI-2NET User Manual Download Page 58

Page: 58 / 93

Shenzhen Coolmay Technology Co.,Ltd

CX-WIFI-2NET module user manual

Page

, Total 93 pages

www.coolmay.com

AT+AABR=on/off<CR>

+ok<CR>< LF ><CR>< LF >

This command enables or disables the adaptive baud rate function, which is enabled

by default.

3.2.2.2.35 AT+DHCPDEN

Function: Enable/disable DHCP server function of LAN port

Format:

AT+DHCPDEN=on/off<ID><CR>

+ok=<ID><CR>< LF ><CR>< LF >

parameter:

This command enables or disables the DHCP server function of the LAN port. The

default is enabled.

3.2.2.2.36 AT+HIDESSID

Function: Turn on/off to hide the SSID of the module AP

Format:

AT+HIDESSID=on/off<CR>

+ok<CR>< LF ><CR>< LF >

This command enables or disables the hiding of the SSID of the module AP. The

default is off.

3.2.2.2.37 AT+DOMAIN

Function: Set/Query the domain name of the login module webpage Format:

Query: AT+DOMAIN<CR>

+ok=<name><CR>< LF ><CR>< LF >

Settings: AT+ DOMAIN=<name ><CR>

+ok<CR>< LF ><CR>< LF >

parameter:

Name: The domain name of the login module web page.

Summary of Contents for CX-WIFI-2NET






























































































Search results

Summary of Contents for CX-WIFI-2NET

Reviews:

Related manuals for CX-WIFI-2NET

Brands by name

Popular brands

Coolmay CX-WIFI-2NET, User Manual

Search results

Summary of Contents for CX-WIFI-2NET

Reviews:

Related manuals for CX-WIFI-2NET

Brands by name

Popular brands