manualshive.com logo in svg

CoolAutomation CoolMasterNet, Manual, Page: 9 / 47

Share
Download
CoolAutomation CoolMasterNet Manual Download Page 9

Connections

CoolMasterNet PRM   Rev 0.7

9

www.coolautomation.com

© 2017 CoolAutomation

ModBus RTU 

CoolGate 4

CG4

L3,L4,L5,L6,L7

ModBus RTU 

CoolGate 5

CG5

L3,L4,L5,L6,L7

ModBus IP

Ethernet

SDDP

Ethernet

ASCII I/F

RS232, Ethernet

CoolRemote

Ethernet

4.3 RS232 Port

RS232 Interface on CoolMasterNet is available from the RS232 DB9 female connector. Below is a DB9
connector front view and signals table.

DB9 Pin

Signal Lvel

Description

2

±12V

TxD (Data from 

CoolMasterNet to DTE

)

3

±12V

RxD (Data from DTE to 

CoolMasterNet

)

5

GND

Ground

1,4,6,7,8

Not Connected

Gender and pinouts of the RS232 cable supplied with CoolMasterNet are suitable for connection to PC RS232
port directly or via standard RS232 to USB adapter. Maximal length of the RS232 Cable should not exceed 25m.
By default RS232 Interface is dedicated for 

ASCII I/F

. The default CoolMasterNet RS232 Port settings are:

Baud Rate

9600

Data Bits

8

Parity Control

None

Stop Bits

1

Flow Control

None

 

4.4 Ethernet

CoolMasterNet incorporates an IEEE 802.3 compatible 10/100 Mb/s Ethernet port supported via RJ45
connector. Below are main port features.

Parameter

Value

Notes

Max Ethernet Cable Length

137m

CAT5 twisted pair cable

Bit Rate

10/100 Mb/s

Supported Ethernet Protocols

10BASE-T/100BASE-TX

Protocol Auto-Negotiation

Enabled

Against Link Partner

Summary of Contents for CoolMasterNet
















































Reviews:

No comments