manualshive.com logo in svg

CoolAutomation CoolMasterNet, Manual, Page: 42 / 47

Share
Download
CoolAutomation CoolMasterNet Manual Download Page 42

ASCII I/F

CoolMasterNet PRM   Rev 0.7

42

www.coolautomation.com

© 2017 CoolAutomation

ON/OFF control of the Water Heater Unit is performed with regular 

on

 and 

o f f

 commands.

EXAMPLE

Set Hot Mode on Water Heater Unit 101 on Line L1

>

wh L1.101 w         

OK       

            

Set Altherma Unit 000 on Line L4 Tank Set Temperature to 40º

>

wh L4.000 t40       

OK       

            

Turn on Tank of Altherma Unit 000 on Line L4

>

wh L4.000 t+        

OK       

            

Turn on Tank Booster of Altherma Unit 000 on Line L4

>

wh L4.000 b+        

OK       

            

Print Tank status of Altherma Unit 000 on Line L4

>

wh L4.000           

L4.000 ON  40C 35C +

 

OK       

            

main

SYNOPSIS

main [Ln]
main <

UID_STRICT

> <0|1>

DESCRIPTION

Change or query Daikin Indoor Units main RC setting. Without parameters 

main

 command will list main RC

setting of all Daikin Indoor Units on all lines. Line number Ln can be indicated to list Daikin Indoor Units on
specific line.

Main RC setting

Description

+

Indoor Unit is main RC

-

Indoor Unit is not main RC

?

No main RC in the system

Notes:
To set Indoor Unit as main RC the previous main RC have to be unset first.

EXAMPLE

List main RC setting of Indoor Units on line L2

>

main L2       

L2.200 -       
L2.201 -       
L2.202 -       
L2.203 -       
L2.204 -       
L2.205 -       
L2.206 +       
OK             

List main RC setting of all Indoor Units

>

main          

Summary of Contents for CoolMasterNet
















































Reviews:

No comments