manualshive.com logo in svg

CoolAutomation CoolMasterNet, Manual, Page: 28 / 47

Share
Download
CoolAutomation CoolMasterNet Manual Download Page 28

ASCII I/F

CoolMasterNet PRM   Rev 0.7

28

www.coolautomation.com

© 2017 CoolAutomation

Notes:
Subnet ID and Device ID of HDL RS485 line can be changed with 

line myid

 command.

EXAMPLE

List existing AC configurations

>hdl                                                    

Ch | AC | En |     Remark     |   CA   | CHFAD | AHML | 
--- ---- ---- ---------------- -------- ------- ------  
1  |  1 |  1 | L1.100         | L1.100 | ++--- | -+-+ | 
2  |  2 |  1 | L1.101         | L1.101 | ++++- | ++++ | 
OK

                                                      

Delete AC configuration for Indoor Unit L1.101

>hdl - L1.101                                           

OK

                                                      

Create AC configuration for Indoor Unit L2.301: channel=2, AC number=2, valid, modes=cool heat, fan
speeds=high medium

>hdl + L2.301 2 2 1 ++----+-+                           

OK

                                                      

HDL ethernet status

>hdl eth                                                

status    : enabled                                     
ID        : 0x01 0x63                                   
send cntr : 0                                           
recv cntr : 0                                           
crc cntr  : 0                                           
OK

                                                      

Enable HDL over ethernet

>hdl eth enable                                         

OK, Boot Required!

                                      

Change HDL ID of CoolMasterNet: Subnet ID=0x01=1, Device ID=0x63=99

>hdl eth myid 0163                                      

OK, Boot Required!

                                      

simul

SYNOPSIS

simul [Ln] <CNT>

DESCRIPTION

Simulate <CNT> Indoor Units on HVAC Line <Ln>. If <Ln> is omitted the first not "Unused" HVAC Line will be
taken. Simulation is not persistent and CoolMasterNet reset will terminate it. 

EXAMPLE

Simulate 5 Indoor Units on HVAC Line L2

>

simul L2 5                 

OK                          

gpio

SYNOPSIS

g p i o
gpio func <A|B|C|D> <GPIO_FUNCTION>

Summary of Contents for CoolMasterNet
















































Reviews:

No comments