Coolair MNBCDD36J Installation, Operation And Maintenance Instructions Download Page 12

Page: 12 / 12

WARNING

—– Moving Parts —–

Disconnect power

before servicing the

fan

WARNING

—– High Voltage —–

Disconnect power

before servicing the

fan

WARNING

Precision Bearings

Do Not

Pressure Wash at

blade assembly center

DO NOT

INSTALL FAN WITH MOVING PARTS WITHIN 8

FEET OF FLOOR OR GRADE LEVEL WITHOUT A GUARD
THAT COMPLIES WITH OSHA REGULATIONS.

DO NOT

USE UNLESS ELECTRICAL WIRING COMPLIES WITH
ALL APPLICABLE CODES.

DO NOT

WIRE WITHOUT

PROVIDING FOR A POWER SOURCE DISCONNECT AT
THE FAN ITSELF.

DO NOT

SERVICE EXCEPT BY A

QUALIFIED MAINTENANCE TECHNICIAN AND ONLY
AFTER DISCONNECTING THE POWER SOURCE.
FAILURE TO OBSERVE THESE PRECAUTIONS CAN
RESULT IN SERIOUS INJURY OR DEATH.

WARNING

CAUTION

FARM PRODUCTS DIVISION

MEMBER OF AMCA

AMERICAN COOLAIR CORPORATION

P.O. BOX 2300

JACKSONVILLE, FLORIDA 32203

PHONE (904) 389-3646 FAX (904) 387-3449

E-MAIL - [email protected]

Form 912-25-2a (October, 2018)

Summary of Contents for MNBCDD36J













Search results

Summary of Contents for MNBCDD36J

Reviews:

Related manuals for MNBCDD36J

Brands by name

Popular brands

Coolair MNBCDD36J, Installation, Operation And Maintenance Instructions

Search results

Summary of Contents for MNBCDD36J

Reviews:

Related manuals for MNBCDD36J

Brands by name

Popular brands