manualshive.com logo in svg

COOL BOSS CB-20SL, Installation And Operation Manual, Page: 24 / 36

Share
Download
COOL BOSS CB-20SL Installation And Operation Manual Download Page 24

 

Cool Boss Evaporative Air Cooler 

24

 

P/N 5900275 — January 2022 — Rev. A

 

Operation 

This section describes how to operate your Cool Boss Evaporative Cooler. 

⚠

 

WARNING

 

The Cool Boss should only be operated by authorized, trained personnel. That 
training includes reviewing and understanding the Operation Manual and safety 

Labels on the Cool Boss. Do 

not

 allow children or impaired persons to operate the 

Cool Boss. 

⚠

 

WARNING

 

Never roll anything heavy or sharp over the power cord.

 Try to find a 

location where people will not be constantly walking over the power cord, 

presenting a tripping hazard. The product should only be operated by authorized, 
trained personnel. 

⚠

 

WARNING

 

Rotating Fan Blades! Keep hands, fingers and loose clothing away from the Fan 
when it is running. 

⚠

 

WARNING

 

Never operate the Cool Boss unless the Ground Fault Circuit Interrupter (GFCI) is 
functioning. 

⚠

 

WARNING

 

Never

 remove the Ground Prong from the plug end of the Power Cord. 

⚠

 

WARNING

 

Do 

not

 run the Power Cord under a rug or other flammable material. 

⚠

 

WARNING

 

Use only in a well ventilated open environment with a fresh air supply. 

⚠

 

WARNING

 

The Cool Boss area must be free from airborne pollutants, flammable gases and 
contaminates. 

⚠

 

WARNING

 

Ambient operating temperature must remain between 65˚ to 113˚ F / 18˚ to 45˚ C 

⚠

 

WARNING

 

Never spray unit with water as moisture may harm the motor or other electrical 
system components. 

⚠

 

WARNING

 

Do 

not

 operate near open containers of flammable liquids or gases. 

⚠

 

WARNING

 

Always maintain a minimum distance of 50 feet / 15 meters from any open flame or 
sparks. 

⚠

 

WARNING

 

The Cool Boss is not designed to be used by children or persons with reduced 
physical, sensory or mental capabilities or lack of experience and knowledge unless 

they have been given supervision or instruction concerning use by a person 

responsible for their safety. 

⚠

 

WARNING

 

Never operate the Cool Boss unless the Cooling Media is securely in place. 

⚠

 

WARNING

 

Always dry the Media after use by pressing the 

Cool

 button twice to run the Fan 

without circulating water. This may take from 15 to 45 minutes depending on the 
current temperature and humidity. 

 

 

Summary of Contents for CB-20SL





































Reviews:

No comments