COOK SQN Series Installation, Operation And Maintenance Manual Download Page 9

9

SQN IO&M

B51141-004

Troubleshooting

Problem and Potential Cause

Low Capacity or Pressure: 

• Incorrect direction of rotation. Make sure the fan rotates 

in same direction as the arrows on the motor or belt drive 

assembly.

• Poor fan inlet conditions. There should be a straight clear 

duct at the inlet.

• Improper wheel alignment.

Excessive Vibration and Noise: 

• Damaged or unbalanced wheel.
• Belts too loose; worn or oily belts.
• Speed too high.
• Incorrect direction of rotation. Make sure the fan rotates 

in same direction as the arrows on the motor or belt drive 

assembly.

• Bearings need lubrication or replacement.
• Fan surge.

Overheated Motor: 

• Motor improperly wired.
• Incorrect direction of rotation. Make sure the fan rotates 

in same direction as the arrows on the motor or belt drive 

assembly.

• Cooling air diverted or blocked.
• Improper inlet clearance.
• Incorrect fan RPMs.
• Incorrect voltage.

Overheated Bearings: 

• Improper bearing lubrication
• Excessive belt tension. 

Parts Lists

SQN-B/SQN-HP

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

Airflow

16

17

18

Part 

No.

Description

Sizes 60 - 165

Sizes 180 - 210

Sizes 225 - 402

1

L-Bolt (2)

L-Bolt (2)

L-Bolt (2)

2

Motor Plate (1)

Motor Plate (1)

Motor Plate (1)

3

Motor (1)

Motor (1)

Motor (1)

4

Motor Support 

Bracket (2)

Motor Support 

Bracket (2)

Motor Support 

Bracket (2)

5

Motor Support Rail 

(2)

Motor Support Rail 

(3)

Motor Support Rail 

(2)

6

Housing Panel 

Motor Side (1)

Housing Panel 

Motor Side (1)

Housing Panel 

Motor Side (1)

7

Access Panel (3)

Access Panel (3)

Access Panel (3)

8

Bearing Support 

Reinforcement Plate 

(1)

Bearing Support 

Reinforcement Plate 

(1)

Bearing Support 

Reinforcement Plate 

(2)

9

Belt Cover (1)

Belt Cover (1)

Belt Cover (1)

10

Bearing Support & 

Bearing Support Leg

Bearing Support & 

Bearing Support Leg

Bearing Support & 

Bearing Support Leg

11

Inlet Panel (1)

Inlet Panel (1)

Inlet Panel (1)

12

Housing Frame 

Support (6)

Housing Frame 

Support (6)

Housing Frame 

Support (6)

13

Inlet Cone, Sizes 

135-402 (1)

Inlet Cone, Sizes 

135-402 (1)

Inlet Cone, Sizes 

135-402 (1)

14

Wheel (1)

Wheel (1)

Wheel (1)

15

Shaft (1)

Shaft (1)

Shaft (1)

16

Bearing Cover (1)

Bearing Cover (1)

Bearing Cover (1)

17 Housing Frame Rail 

(2)

Housing Frame Rail 

(2)

Housing Frame Rail 

(2)

18

Bearing (2)

Bearing (2)

Bearing (2)

Summary of Contents for SQN Series













Reviews: