background image

                                           CONTROLS, INCORPORATED 

C O N T R O L   S Y S T E M S   &   S O L U T I O N S  

                                                                                                            

                                                                                                                  - 20 - 

13) Warranty 

CONTROLS, INC. is herein called “Seller”.  The person, firm or corporation to whom or 
which the sale is made is herein called “Buyer”.  Seller warrants to the Buyer that all 
products furnished under this order will conform to Seller’s specification, drawings as 
described in its current catalog or quotation and will be free from defects in materials 
and workmanship.  Seller must approve other special requirements asked for by the 
Buyer in its purchase order in writing.  Parts replaced or repaired in the warranty period 
shall carry the unexpired portion of the original warranty.  The foregoing is subject to the 
provisions that in no case will the total warranty period extend beyond twelve (12) 
months from date seller ships equipment from point of sale. 
 
The Liability of Seller hereunder is limited to replacing or repairing 

at Seller’s factory 

any part or parts which have been returned to the Seller and which are proved by buyer 
as defective or not conforming to Seller’s specifications, drawings or other written 
descriptions, accepted by Seller, provided that such part or parts are returned by the 
buyer within thirty (30) days after such defect is discovered.  All items returned to Seller 
for repair or replacement must be sent freight prepaid to its factory.  Buyer must obtain 
Seller’s Return Merchandise Authorization # prior to returning items.  The above 
conditions must be met if warranty is valid.  Seller will not be liable for any damage 
done by unauthorized repair work, or unauthorized misapplication in non-suitable 
environment. 
 
In no event shall the Seller be liable for loss, damage, or expense directly or indirectly 
arising from the use of the units, or from any other cause, except as expressly stated in 
the warranty.  Seller makes no warranties, express or implied, including any warranty 
as to merchantability of fitness for a particular purpose or use.  Seller is not liable for 
and buyer waives any right or action it has or may have against seller for any 
consequential or special damages arising out of any breach of warranty, and for any 
damages buyer may claim for damage to any property or injury or death to any person 
arising out of its purchase or the use, operation or maintenance of the product.  Seller 
will not be liable for any labor subcontracted or performed by buyer for preparation of 
warranted item for return to 

Seller’s factory or for preparation work for field repair or 

replacement.  The Seller will not consider invoicing of Seller for labor either performed 
or subcontracted by buyer as a liability.  This warranty shall be exclusive of any and all 
other warranties express or implied and may be modified only by a writing signed by an 
officer of the Seller.  With respect to accessories supplied by Seller, but manufactured 
by others, there is no warranty of any kind, express or implied, and specifically there is 
no warranty of merchantability or fitness, except as may be set forth in any warranty the 
manufactures have made to Seller and which can be passed to the Buyer.  

  

Summary of Contents for C3M-115






















Reviews: