background image

In addition to the device mode window, system mode can be accessed as well. 

 

Although under normal circumstances you should never encounter this window, if by accident 
you should happen to come across it, simply press the up or down arrow until the window reads 
“run”. Press and hold the 

button for 3 seconds, and the display will return to device mode. 

Additionally, should for any reason the display lettering become red instead of green, you will 
need to access system mode to run the program in this fashion. Holding the 

 key while 

pressing up and down allows you to change between system mode and device mode. A third 
mode, which will display TRM on the left side of the screen, can also be accessed. Cycle through 
until the appropriate mode is displayed. 

Finally, it is possible to lock the keypad. Should you inadvertently do so, press and hold 
the

button and an arrow key together for 3 seconds to unlock the keypad again. 

Security Begins With Controlled Access 

1636 W. 130th Street, Brunswick, OH 44212 

Toll Free Phone: (800) 942-0829 | Fax: (800) 942-0828 / Phone: (330) 273-6185 | Fax: (330) 273-4468 

18

Summary of Contents for BE800-R






















Reviews: