manualshive.com logo in svg

Control Techniques UD53, User Manual

Share
Download
Control Techniques UD53 User Manual Download Page 31

UD53 User Guide
Issue code:   53nu3

C-1

C

Diagnostics

C.1 Trip 

codes

The following trip codes are associated with the UD53:

Drive
display

No.

Conditions

SEP

9

Internal fault in the UD53, or connections to the UD53 have not been made.

ENC.PH7

17

The 

SIN

 and 

COS

 connections from the resolver are incorrectly made or the phase

sequence of the motor connections is reversed.

ENC.PH8

18

Resolver phasing test or magnetizing current test prematurely ended.

ENC.PH9

181

Closed-loop Vector:   Loss of resolver output signals.

Servo mode:   Resolver and/or motor phase connections incorrect, causing reverse
torque to be produced.

SEP.diS

180

The type of small option module that the Drive has been programmed to operate
with has been removed or is not fitted correctly.

Perform either of the following:

Ensure the appropriate type of small option module is correctly fitted

To operate the Drive in the present configuration, set parameter 

00

 at 

1000 

and

press the 

STOP/RESET 

key.

Summary of Contents for UD53



































Reviews:

No comments

Brands by name

Popular brands

Load more brands