background image

© 2016 

CONTRIVE • B14

88|

QBK

.EN 

0219

 

12

 

www.contrive.it 

PROGRAM SEQUENCE 

 

SELF TEST

 IS PERFORMED  AT POWER-

ON, ONCE SUCCESSFULLY COMPLETED 

BURNER IS READY TO S

TART. 

 

 

IF  THE  UNIT  HAS  BEEN

  TURNED OFF 

WHILE IN 

LOCKOUT

 OR PARAMETER 101 

HAS BEEN SET  TO 

STANDBY

, IT WILL BE 

NECESSARY TO PUSH THE 

BUTTON  OR 

ISSUE  A  FIELDBUS  COM

MAND TO EXIT 

FROM NON-

VOLATILE LOCKOUT

  

 

THE  BURNER  REMAINS  I

SHUTDOWN

 

UNTIL THE THERMOSTAT 1 IS CLOSED OR 

A REMOTE RUN COMMAND IS RECEIVED 

FROM FIELDBUS.

  

 

 

 

FLAME SIMULATION

 VERIFIED WHILE IN 

WAITING OR PREPURGE. 

 
 

 

AFTER PRESET 

WAITING OR PREPURGE

 

TIME HAS ELAPSED, IGNITION  DEVICE   

ACTIVATED  AND VERIFIED, THEN THE 

PILOT VALVE IS OPEN.  

 
 

 

PILOT PROVING STARTS IF THE FLAME IS 

DETECTED WITHIN THE 

SAFETY TIME

.  

 

 

 

IF NO FLAME IS DETECTED  WITHIN THE 

SAFETY  TIME,  A  LOCK

OUT OCCURS. 

DEPENDING ON PARAMET

ER  403  THE 

UNIT COULD CARRY OUT  UP TO THREE 

FURTHER 

START-UP ATTEMPTS

 

AFTER THE PILOT  PROVING THE MAIN 

VALVE OPENS. AT THE END OF 2

ND

  

SAFETY TIME THE PILOT FUEL VALVE IS 

TURNED OFF (INTERRUPTED MODE) OR 

REMAINS OPEN (INTERMITTENT MODE). 

MAIN VALVE

 

CONTROLLED  BY  MEANS 

OF THERMOSTAT 2 OR F

IELDBUS.

 

 

 

FLAME FAILURE

 DURING OPERATION LEADS TO 

LOCK

OUT, IGNITION RESTORATION OR RECYCLE (PARAMETER 

504).

 

 

 

AIR FAILURES

 DURING OPERATION LEADS TO IMMEDIATE 

LOCKOUT OR RECYCLE D

EPENDING ON PARAMETER 507. 

 

 

SHUTDOWN REQUEST

  (THERMOSTAT 1 OR FIE

LDBUS  COMMAND)  WILL  TURN  OFF  THE  BURNER,

  WAITING FOR ALLOWED 

POSTCOMBUSTION  AND  O

PTIONAL POSTPURGE. AN  OPTIONAL 

ADJUSTABLE 

MINIMUM COMBUSTION TIME

  ENSURES THAT 

THE  BURNER  BURNS  FOR

  A DEFINED PERIOD,  EVEN IF THE THERMOSTAT 1 IS SWITCHED OFF  OR AN  HALT COMMAND IS 

RECEIVED THROUGH FIE

LDBUS BEFOREHAND.

  

 

 

 

 

FIRING SYSTEMS OPERATING 

ABOVE 750°C

 ARE 

CONSIDERED TO BE 

HIGH TEMPERATURE EQUIPMENT

 

(SEE EN 746

-2): FLAME 

PRESENCE MUST BE VER

IFIED UNTIL THE FURN

ACE IS BELOW 750°C

BYPASS REQUEST CAN B

E ISSUED THROUGH A CONTACT AT 

TERMINAL 17 (HANDLED 

BY

 SAFETY TEMPERATURE M

ONITOR, DIN 3440). 

 

RECEIVING  A  VALID  BY

PASS REQUEST,  THE INTERNAL FLAME C

ONTROL  SYSTEM  IS  BYP

ASSED AND THE FUEL  VALVES ARE 

OPENED WITHOUT FLAME SUPERVISION: THE 

SYSTEM WORKS

 

AS USUAL BUT WITHOUT

 FLAME MONITORING. 

THE BURNER IS TURNED

 ON DIRECTLY (NO SAFETY TIME, NO IGNITION TRANSFORMER) WHEN TEMPERATURE IS 

ABOVE 750°C. 

WHEN THE TEMPERATURE IN T

HE FURNACE DROPS BEL

OW 750°C THE REMOTE 

CONTROL MUST BE RELE

ASED. 

 

 

 

RESET 

 

A reset action is supposed to be a clear defined manual action. An automatic reset is not allowed by EN 13611:2015. 

When manual action is initiated from remote 

by means of RESET INPUT at terminal 14 or through the FIELDBUS 

CONTROL, without being within the visible sight of the appliance: 

 

actual status and relevant information of the process shall be visible to the user, 

 

QBK limits the m

aximum number of resets to 5 actions within a span of 15 minutes. 

Lockout (resettable only from local button) exceeding this limit. 

 

 

Summary of Contents for QBK





















Reviews: