Continental Fireplaces CLHD45N Installation And Operating Instructions Manual Download Page 8

8

W415-0895 / C / 03.13.12

2.4  RATING PLATE INFORMATION

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to 
the model, venting and gas type of the appliance.

For rating plate location, see “INSTALLATION OVERVIEW” section.
This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

W385-0497 / D

&(57,),('81'(5+202/2*8(6(/21/(61250(6$16,=E‡&6$E9(17('*$6),5(3/$&()2<(5$8*$=9(17,/e

DIRECT VENT GAS FIREPLACE HEATER. APPROVED FOR BEDROOM, BATHROOM AND BED-SITTING 
ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE 
WITH THE CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, 
IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONSTRUCTION AND 

6$)(7< 67$1'$5' 7,7/(  &)5 3$57  :+(1 7+,6 86 67$1'$5' ,6 127
$33/,&$%/(86(7+(67$1'$5')25),5(6$)(7<&5,7(5,$)250$18)$&785('+20(

INSTALLATIONS, SITES AND COMMUNITIES, ANSI / NFPA 501A. THIS APPLIANCE MUST BE 

,167$//(',1$&&25'$1&(:,7+/2&$/&2'(6,)$1<,)121()2//2:7+(&855(17

ANSI Z223.1, OR CSA B149, INSTALLATION CODES.

)2<(5'(&+$8))$*($8*$=$9(&e9$&8$7,21+202/2*8e3285,167$//$7,21'$1681(
&+$0%5( ¬ &28&+(5 81( 6$//( '( %$,1 (7 81 678',2$335235,e 3285 ,167$//$7,21

DANS UNE MAISON MOBILE SI SON INSTALLATION CONFORME AUX EXIGENCES DE LA 

1250(&$1&6$=0+6e5,('(0$,621602%,/(6e48,3e(6$8*$=(19,*8(85$8
&$1$'$ 28 $8; e7$7681,6 '( /$ 1250( '( 6(&85,7e (7 '( &216758&7,21 '(
0$,62160$18)$&785e(67,75(&)56(&7,21'$16/(&$628&(77(1250(
'e7$7681,61(3(87Ç75($33/,48e(6(5e)e5(5$/$1250(5(/$7,9($8&5,7Ê5(
'( 0(685(6 '( 6e&85,7e &2175( /,1&(1',( 3285 /(6 ,167$//$7,216 '$16 /(6
0$,6216 0$18)$&785e6 /(6 6,7(6 (7 /(6 &20081$87e6$16,1)3$ $ &2'(6
,167$//(5/¶$33$5(,/6(/21/(6&2'(6285Ê*/(0(176/2&$8;28(1/¶$%6(1&(
'(7(/65Ê*/(0(1766(/21/(6&2'(6'¶,167$//$7,21$16,=28&6$%(1

VIGUER.

 

9700539 (WSL) 

 

4001657 (NGZ) 

 4001658 

(NAC) 

 

4001659 

(WUSA)

 LHD45N CLHD45N 

MODEL 

CLHD45P 

LHD45P

 

 

)7P

$/7,78'(e/e9$7,21

)7P

 

 

24,000 BTU/h 

INPUT / ALIMENTATION 

24,000 BTU/h

3.5" WATER COLUMN/D'UNE COLONNE D'EAU 

MANIFOLD PRESSURE/PRESSION AU COLLECTEUR: 

 

10" WATER COLUMN/D'UNE COLONNE D'EAU 

4.5" WATER COLUMN/D'UNE COLONNE D'EAU 

MINIMUM SUPPLY PRESSURE/PRESSION D'ALIMENTATION MINIMALE:

 

11" WATER COLUMN/D'UNE COLONNE D'EAU

7.0" WATER COLUMN/D'UNE COLONNE D'EAU 

MAXIMUM SUPPLY PRESSURE/PRESSION D'ALIMENTATION MAXIMALE:

 

13" WATER COLUMN/D'UNE COLONNE D'EAU

NOT FOR USE WITH SOLID FUEL. FOR USE WITH GLASS 
DOORS CERTIFIED WITH THIS UNIT ONLY.

WARNING: 

'2127$''$1<0$7(5,$/727+($33/,$1&(:+,&+:,//&20(

IN CONTACT 

:,7+7+()/$0(627+(57+$17+$76833/,('%<7+(0$18)$&785(5:,7+7+($33/,$1&(

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS /

'e*$*(0(1760,1,0$8;'(60$7e5,$8;&20%867,%/(6

TOP/ DESSUS 

0” 

RECESSED DEPTH / PROFONDEUR D'ENCASTRE 

20.5”

FLOOR / PLANCHER 

0” 

)5$0,1*127,1&/8',1*)$&(0$7(5,$/266$785(0$7e5,$8'()$d21121&2035,6

6,'(6&Ð7e6

³

%$&.$55,Ê5(

´

9(17723'(6686'8&21'8,7'¶e9(17

9(176,'(6 %27720&Ð7e6(7'(66286'8&21'8,7'e9(17

9(57,&$/9(17&21'8,7'¶e9(179(57,&$/

MANTEL / TABLETTE 

6" *

TOP, SIDES & BACK: PER STAND OFF SPACERS FOR FRAMING MATERIALS. FOR FINISHING MATERIALS
SEE OWNERS MANUAL

'(6686&27e6 $55,Ê5(6(/21/(6(63$&(856'('e*$*(0(173285/(60$7e5,$8;
'266$785(6(/21/$0$18(/'(35235,e7$,5(3285/(60$7e5,$8;'(),1,7,21

* MAXIMUM HORIZONTAL EXTENSION / L'EXTENSION HORIZONTALE MAXIMALE: 2". SEE INSTRUCTION 

0$18$/)25*5($7(5(;7(16,2165e)e5(5$80$18(/',16758&7,213285'(6

EXTENSIONS PLUS GRANDES.
SEE OWNER'S INSTRUCTION MANUAL FOR MINIMUM AND MAXIMUM VENT LENGTHS.
REFERER AU MANUEL D'INSTALLATION DE PROPRIETAIRE POUR LES LONGUEURS 
D'EVACUATION MINIMALE ET MAXIMALE.

UN COMBUSTIBLE SOLIDE NE DOIT PAS ÊTRE UTILISÉ 
AVEC CET APPAREIL. UTILISER AVEC LES PORTES 
VITRÉES HOMOLOGUÉES SEULEMENT AVEC CETTE UNITÉ.

AVERTISSEMENT:

 

1¶$-287(=3$6$&(7$33$5(,/$8&810$7e5,$8'(9$17(175(5

EN CONTACT AVEC LES FLAMMES AUTRE QUE CELUI QUI EST FOURNI AVEC CET APPAREIL PAR 
LE FABRICANT.  

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE NAPOLEON VENT KITS. SEE 
OWNERS INSTALLATION MANUAL FOR VENTING SPECIFICS. PROPER REINSTALLATION AND 

5(6($/,1*,61(&(66$5<$)7(56(59,&,1*7+(9(17$,5,17$.(6<67(0
/$33$5(,/'2,7e9$&8(56(6*$=(187,/,6$17/(16(0%/('e9$&8$7,2135235($
1$32/(215e)e5(5$80$18(/',167$//$7,21'(35235,e7$,5(3285/e9$&8$7,21
35e&,6(,/(67,03257$17'(%,(15e,167$//(5(75(6&(//(5/e9(17$35(6$92,5
$6685e/(0$,17,(1'86<67e0('(35,6('$,5

ELECTRICAL RATING: 115V, 60HZ. LESS THAN 12 AMPERES

63e&,),&$7,216e/(&75,48(69+=02,16'($03Ê5(

WOLF STEEL LTD.

24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA

SERIAL

180%(512'(6e5,(

LHD45

SAMPLE

E

*$6),5

*$6)

$=$9(&e9$&8

$=$9(&e9$&

81( 6$//( '( %$,1

1( 6$//( '( %$,

ON MOBILE SI SON INS

ON MOBILE SI SON 

6$=0+6e5,('(0$,6216

$=0+6e5,('(0$,6216

8 $8; e7$7681,6 '( /$ 1250(

e7$7681,6 '( /$ 1250

0$18)$&785e(67,75(&)56

785e(67,75(&)5

681,61(3(87Ç75($33/,48e(

7Ç75($33/,48e(

0(685(6 '( 6e&85,7e &2175(

(685(6 '( 6e&85,7e &2175(

$,6216 0$18)$&785e6 /(6 6,7(

$,6216 0$18)$&785e6 /(6 6,7

,167$//(5/¶$33$5(,/6(/21/(6

167$//(5/¶$33$5(,/6(/21/(

'(7(/65Ê*/(0(1766(/21

7(/65Ê*/(0(1766(/2

4001657 (NGZ) 

4001657 (NGZ) 

4001659 (WUSA)

4001659 (WUSA)

PP

ODEL 

ODEL 

CLHD4

CLHD

8'(e/e9$7,21

'(e/e9$7,21

UT / ALIMENTATION

UT / ALIMENTATION 

24

PL

SSURE/PRESSION AU COLLECTEUR

SURE/PRESSION AU C

ESSURE/PRESSION D'ALIMENTATIO

SSURE/PRESSION D'ALIME

RESSURE/PRESSION D'ALIMENTAT

ESSURE/PRESSION D'ALIMENT

LASS 

LASS 

/&20(

20(

IN CONTACT 

IN CONTACT 

:,7+7+($33/,$1&(

7+($33/,$1&(

D'ENCASTRE 20.5”

'ENCASTRE

$7e5,$8'()$d21121&2035,6

5,$8'()$d21121&2035,6

´

´

8,7'e9(17

OR FRAMING MATERIALS. FOR FINIS

OR FRAMING MATERIALS. FOR FIN

3$&(856'('e*$*(0(173285/(

(856'('e*$*(0(173285/

e7$,5(3285/(60$7e5,$8;'(

,5(3285/(60$7e5,$8;'(

SION HORIZONTALE MAXIMA

ON HORIZONTALE MAXI

5e)e5(5$80$18(/'

5e)e5(5$80$18(/

MINIMUM AND

MINIMUM AND

ROPRIETA

OPRIETA

UN COM

UN COM

AVEC

AVE

VIT

VIT

A

7.1A

THIS APPLIANCE USES A 4” EXHAUST / 7” AIR INTAKE VENT PIPE SYSTEM.

Refer to the section applicable to your installation. 

For safe and proper operation of the appliance follow the venting instruction exactly. Deviation from the 
minimum vertical vent length can create dif

fi

 culty in burner start-up and/or carboning. Under extreme vent 

con

fi

 gurations, allow several minutes (5-15) for the 

fl

 ame to stabilize after ignition. Provide a means for 

visually checking the vent connection to the appliance after the appliance is installed. Use a 

fi

 restop, vent pipe 

shield or attic insulation shield when penetrating interior walls, 

fl

 oor or ceiling.

NOTE: If for any reason the vent air intake system is disassembled; reinstall per the instructions 
provided for the initial installation.

!

WARNING

RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.

IF VENTING IS INCLUDED WITH SPACERS THE VENT SYSTEM MUST BE SUPPORTED EVERY 3 FEET 

FOR BOTH VERTICAL AND HORIZONTAL RUNS. USE SUPPORTS OR EQUIVALENT 

NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE REQUIRED CLEARANCE FROM 

COMBUSTIBLES. USE WOLF STEEL LTD. SUPPORT RING ASSEMBLY W010-0370 OR EQUIVALENT 

NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE MINIMUM CLEARANCE TO COMBUSTIBLES 

FOR BOTH VERTICAL AND HORIZONTAL RUNS. SPACERS ARE ATTACHED TO THE INNER PIPE AT 

PREDETERMINED INTERVALS TO MAINTAIN AN EVEN AIR GAP TO THE OUTER PIPE. THIS GAP IS 

REQUIRED FOR SAFE OPERATION. A SPACER IS REQUIRED AT THE START, MIDDLE AND END OF 

EACH ELBOW TO ENSURE THIS GAP IS MAINTAINED. THESE SPACERS MUST NOT BE REMOVED. 

3.0 VENTING

Summary of Contents for CLHD45N

























































Reviews: