English
- 11 -
Switching On/Off
To Switch the TV On
Connect the power cord to a power source such as a
wall socket (220-240V AC, 50 Hz).
To switch on the TV from standby mode either:
• Press the
Standby
button,
Pro/-
or a
numeric button on the remote control.
• Press the control button on the TV.
To Switch the TV Off
• Press the
Standby
button on the remote control.
• Press the control button on the TV, the function
options menu will be displayed. The focus will be
on the
Standby
option. Press and hold the button
for about 2 seconds to activate this option. The icon
colour of the option will change. Then press the
button once again, the TV will switch into standby
mode.
To power down the TV completely, unplug the
power cord from the mains socket.
Note:
When the TV is switched into standby mode, the standby
LED can blink to indicate that features such as Standby Mode
Search, Over Air Download or Timer is active. The LED can
also blink when you switch on the TV from standby mode.
First Time Installation
When turned on for the first time, the language
selection screen is displayed. Select the desired
language and press
OK
. In the following steps of
the installation guide, set your preferences using the
directional buttons and
OK
button.
After the language selection, you will be asked whether
you want to change accessibility settings. Highlight
Yes
and press
OK
to change. Refer to
System Menu
Content
section for detailed information on available
options.
Set your country preference on the next screen.
Depending on the country selection you may be asked
to set and confirm a PIN at this point. The selected PIN
cannot be 0000. You have to enter it if you are asked
to enter a PIN for any menu operation later.
You can activate
Store Mode
option in the next step.
This option will configure your TV’s settings for store
environment and depending on the TV model being
used, the supported features of it may be displayed
on the screen as an info banner or the pre-installed
video file may be played back. This option is intended
only for store use. It is recommended to select
Home
Mode
for home use.
Store mode
option will be
available in
Settings>System>More
menu and your
preference for this setting can be changed later. Make
your selection and press
OK
to continue.
Depending on the model of your TV, the picture mode
selection screen may appear at this point. In order
for your TV to consume less energy and be more
environmentally friendly select
Natural
and press
OK
to continue. If you select
Dynamic
and press
OK
, a
confirmation dialogue will be displayed. Select
Yes
and
press
OK
to proceed. You can change your selection
later using the
Mode
option in the
Settings>Picture
menu.
On next screen you can set broadcast types to be
searched, set your encrypted channel searching
and time zone (depending on the country selection)
preferences. Additionally you can set a broadcast
type as your favourite one. Priority will be given to the
selected broadcast type during the search process
and the channels of it will be listed on the top of the
channel list. When finished, highlight
Next
and press
OK
to continue.
About Selecting Broadcast Type
To turn a search option on for a broadcast type highlight
it and press
OK
, Left or Right directional button. The
checkbox next to the selected option will be checked.
To turn the search option off clear the checkbox by
pressing
OK
, Left or Right directional button after
moving the focus on the desired broadcast type option.
Digital Aerial:
If
D. Aerial
broadcast search option
is turned on, the TV will search for digital terrestrial
broadcasts after other initial settings are completed.
Digital Cable:
If
D. Cable
broadcast search option
is turned on, the TV will search for digital cable
broadcasts after other initial settings are completed. A
dialogue may be displayed depending on the country
selection before starting to search asking whether you
want to perform cable network search. If you select
Yes
and press
OK
you can select
Network
or set values
such as
Frequency
,
Network ID
and
Search Step
on
the next screen. If you select
No
and press
OK
or the
network search dialogue is not displayed you can set
Start
Frequency
,
Stop
Frequency
and
Search Step
on the next screen. When finished, highlight
Next
and
press
OK
button to continue.
Note:
Searching duration will change depending on the
selected
Search Step
.
Analogue:
If
Analogue
broadcast search option is
turned on, the TV will search for analogue broadcasts
after other initial settings are completed.
After the initial settings are completed the TV will start
to search for available broadcasts of the selected
broadcast types.
While the search continues current scan results will be
displayed at the bottom of the screen. You can press
the
Home
,
Back
or
Exit
button to cancel the search.
The channels that have already been found will be
stored in the channel list.
After all the available stations are stored,
Channels
menu will be displayed. You can edit the channel
list according to your preferences using the
Edit
tab
options or press the
Home
button to quit and watch TV.
