Conteg RMS-I-DE-01 User Manual Download Page 5

 

o

 

Maximum  CAT5/6  Extension  Cable  Run  Length:  90  meters  or  300  feet  (1000  feet  when 
connected via dry contact inputs). 

o

 

Radionuclide = Am-241 

o

 

Type of substance (sealed / unsealed) = It is sealed  

o

 

Physical form (solid / liquid / gas) = Solid. 

o

 

Activity in Becquerel’s? = Less than 37,000 Becquerel’s. 

1.4.

 

Smoke Detector OIDs: 

o

 

For normal state, return value = 2 

o

 

For alarm state, return value = 4 

o

 

Note:  You  can  test  the  smoke  detector  by  holding  down  the  test  button  until  the  audible 
alarm occurs - about 5 sec. The smoke detector will then send an alarm signal to the unit. 

Important: 

The Web interface settings for the smoke detector are: 

Direction:

  

 

Input 

Normal State:

    Open/+5 Volts 

2.

 

Important Safety Information 

Observe and follow all local and national electrical and building codes for installation. 

This smoke detector is designed to be used inside a single room only. In multi-room buildings, each 
individual room should have its own smoke detector. This smoke detector is not a substitute for a 
complete fire alarm system. 

Smoke may not reach the smoke detector for many reasons. For example, if a fire starts in a remote 
part of a building or home, on another level, wall, roof, or on the other side of a closed door, smoke 
may not reach the smoke detector in time to alert personnel. In other words the smoke detector will 
not promptly detect a fire except in the area or room in which it is installed. 

The smoke detectors can only sound their alarms when they detect smoke. The smoke detectors 
detect combustion particles in the air. They do not sense heat, flame or gas. This smoke detector is 
designed to give an audible warning of a developing fire. However, many fires are fast-burning, 
explosive, or intentional. Others are caused by carelessness or safety hazards. So always keep in mind 
that smoke may not reach the smoke detector alarm QUCKLY ENOUGH. 

The smoke detectors have limitations. This smoke detector is not foolproof and is not warranted to 
protect lives or property from fire. Smoke alarms are not a substitute for insurance. Business owners 
are responsible for insuring their own lives and property. In addition it is possible for the smoke alarm 
to fail at any time. For this reason, you must test the smoke detectors weekly and replace them every 
10 years. 

Summary of Contents for RMS-I-DE-01
















Reviews: