background image

 

 

 

After inserting the  funnel start  filling or topping up the  extinguishing liquid. Fill slowly as the  inflow 
opening is small. 

 

After filling with the necessary amount of liquid remove the funnel. 

 

After filling, re-screw the filling hole cover and gently tighten 

 

Return the LES-RACK-M1 into the horizontal (working) position and place it back in the box 

 

De-aerate the pump with the “TEST”+ “MUTE ”buttons 

 

CHECKING AND COMMISSIONING 

 

Commissioning 

The procedure for commissioning equipment is given in Table No. 2 “INSTALLATION - ACTIVATION”.

 

 

Checking  

The function of the equipment is checked exclusively in the TEST regime.  
The procedure for commissioning is given in Table No.2 “TEST”. 

 

Disconnecting equipment 

The equipment is disconnected by stopping the supply from the distribution network and, at the same 
time, disconnecting the battery. 
The supply from the distribution network is stopped by disconnecting the circuit breaker (switch) or by 
disconnecting the supply cable from the AC inlet on the equipment. 
The battery is disconnected by pressing and holding the “TEST ”button and pressing the “RESET ”button 
on the front panel of the equipment. 
 

NOTIFICATION: 

   

If equipment is disconnected for more than 4 months it must be connected to the 

network and operated (connect the battery). It must be connected for at least 12 hours to charge the 
backup source (battery). After charging, the equipment must be disconnected and then it is possible to 
put it aside again.

 

 

 

SERVICING 

General requirements 

The LES-RACK-M1 equipment is designed and produced for fully automated operation. The front panel 
contains  the  signal  LED  elements  providing  information  about  the  state  and  running  processes  of  the 
equipment. The list of local signals is given in Table No. 5. 
The cover of the equipment must only be opened by a person authorized by service organization. After 
opening the cover there is a risk of an electric shock. The equipment user must state and train a person 
responsible  for  operation  of  the  equipment,  persons  authorized  to  operate  the  equipment  and 
authorized  maintenance  personnel  who  must  be  familiarized  in  detail  with  this  user  manual.  For 
instructing maintenance employees of other equipment, correct procedures must be put in place so that 
during  their  activities  they  do  not  activate  fire  extinguisher.  It  is  recommended  to  state  that 
unauthorized persons are prohibited or their entrance into premises of the equipment is controlled. 

 

MAINTENANCE 

General provisions 

The  user  must  carry  out  program  inspections,  ensure  planned  repairs  and  keep  records  about 
inspections and repairs. The user must prevent leaks and immediately repair ascertained leaks according 

Summary of Contents for LES-RACK-M1


























Reviews:

Related manuals for LES-RACK-M1