Contec HPC-HLS10 Series Hardware Manual Download

Page: 3 / 39

IPC-PT/MV10 / IPC-PT/LS10 / HPC-HMV10 / HPC-HLS10 Hardware Manual

Table of Contents

Copyright ................................................................................................................................................. i

Trademarks .............................................................................................................................................. i

Table of Contents.................................................................................................................................... ii

INTRODUCTION

Features .............................................................................................................................................1

Limited One-Year Warranty ............................................................................................................1

How to Obtain Service .....................................................................................................................2

Liability.............................................................................................................................................2

Warning ............................................................................................................................................2

Handling Precautions .......................................................................................................................3

OVERVIEW

Specifications...........................................................................................................................................7

Physical Dimensions .............................................................................................................................10

EACH COMPONENT FUNCTION

Component Locations(IPC-PT/MV10 series, IPC-PT/LS10 series) ............................................11

Component Locations(HPC-HMV10 series, HPC-HLS10 series) ...............................................12

Serial Port Interface (COM1, COM2) ...........................................................................................13

Switching COM2 between RS-232C and RS-422A/485 ..............................................................14

COM2 RS-422A/RS-485 data transmission mode setting............................................................15

Terminating resistor setting ...........................................................................................................16

Ethernet (UTP) ...............................................................................................................................18

Keyboard Interface (KB)................................................................................................................19

PCMCIA (PCMCIA)......................................................................................................................20

USB port .........................................................................................................................................21

General-purpose I/O ports (I/O) ....................................................................................................21

Power input terminal strip..............................................................................................................23

External Speaker Output Terminal ................................................................................................24

Touch Panel ....................................................................................................................................24

Setting the SW2 to 4, JP5...............................................................................................................24

Setup of OS operation (SW2) ........................................................................................................25

DIP switch for applications (SW3)................................................................................................25

Summary of Contents for HPC-HLS10 Series








































Search results

Summary of Contents for HPC-HLS10 Series

Reviews:

Related manuals for HPC-HLS10 Series

Brands by name

Popular brands

Contec HPC-HLS10 Series, Hardware Manual

Search results

Summary of Contents for HPC-HLS10 Series

Reviews:

Related manuals for HPC-HLS10 Series

Brands by name

Popular brands