Contec CPS-PCS341EC-DS1-1201 Page 43 Hardware Manual Download

Page: 43 / 44

6 List of Optional Products

CPS-PCS341EC-DS1-1201 Hardware Manual

List of Optional Products

DIN Rail Fitting Power Supply

- CPS-PWD-90AW24-01 : DIN rail fitting power supply 90[w]

(Input: 100 - 240VAC, Output: 24VDC 3.8 A)

- CPS-PWD-30AW24-01 : DIN rail fitting power supply 30[w]

(Input: 100 - 240VAC, Output: 24VDC 1.3 A)

Stacking Type Modules

- CPS-DIO-0808L : with digital input/output (No built-in power supply)

- CPS-DIO-0808BL : with digital input/output (built-in power supply)

- CPS-COM-1PC : with RS232C (contains 1port)

- CPS-COM-2PC : with RS232C (contains 2 ports)

- CPS-COM-1PD : with RS-422A/485 (1 port)

- CPS-COM-2PD : with RS-422A/485 (2 ports)

- CPS-AI-1608LI : with analog input

- CPS-AO-1604LI : with analog output

- CPS-SSI-4P : with temperature sensor input

* Visit the Contec website regarding information on the optional products.

(http://www.contec.com)

Summary of Contents for CPS-PCS341EC-DS1-1201













































Search results

Summary of Contents for CPS-PCS341EC-DS1-1201

Reviews:

Related manuals for CPS-PCS341EC-DS1-1201

Brands by name

Popular brands

Contec CPS-PCS341EC-DS1-1201, Hardware Manual

Search results

Summary of Contents for CPS-PCS341EC-DS1-1201

Reviews:

Related manuals for CPS-PCS341EC-DS1-1201

Brands by name

Popular brands