Contec AO-1604AIN-USB Reference Manual Download Page 62 | Manualshive

Page: 62 / 89

background image

—

Software

—

AO-1604VIN-USB / AO-1604AIN-USB Reference Manual

—

62

—

2.

CONTEC Device Utility

CONTEC Device Utility is utility software to setup the CONTEC's measuring control device. Use this
software to update firmware of the product.

1.

Updating Firmware

Firmware is namely software which is embedded in the product. Up-to-date firmware (update file)
will be supplied in the CONTEC website when function upgrades and so on.
The following presents how to update firmware.

1

Preparation for updating.
First, unplug the USB cable connected to the product.
Then, unplug the external power supply (such as AC adapter) for self-power.
After that, if interface connectors are set to the product, remove all of them once as well.

When using more than one product, always connect each of them with a USB cable, and
complete updating before starting to update the next product.
Set Module ID of this product to FFh. (Remeber the present ID before setting it to FFh.)
This setting is specifically used for firmware updating.

2

Connect the external power supply (such as AC adapter) for self-power to the product.

3

Connect the product to USB port of the PC.

«
...
60
61
62
63
64
...
»

Summary of Contents for AO-1604AIN-USB


























































































Reviews:

No comments

Related manuals for AO-1604AIN-USB

Brand: Magtek Pages: 26

Brand: Magtek Pages: 35

Brand: Beckhoff Pages: 39

Brand: Nailor Pages: 10

AKI-CDT-MOD-15T

Brand: Kollmorgen Pages: 28

Brand: CCV Pages: 25

Genion II PN223

Brand: Intralot Pages: 20

Brand: Aratek Pages: 13

Brand: SERRA Soldadura Pages: 17

Brand: UIC Pages: 4

Brand: Hanasis Pages: 11

Brand: ICP Pages: 31

Brand: Partner Pages: 2

Brand: NEO Pages: 21

UNIVERGE SL2100

Brand: NEC Pages: 26

Brand: HIKVISION Pages: 2

Brand: HIKVISION Pages: 2

Brand: barclaycard Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands