Contacta STS-K070 Installation & User Manual Download Page 15 | Manualshive

Page: 15 / 20

background image

15

Factory Default Settings

To return the amplifier the factory default settings:

1. Unplug the power supply and then reconnect it.

2. Press the On/Off button and Volume In (-) button together, then release.

3.

The Volume In LED bar will have all LEDs illuminated, while the Volume

Out LED bar will display the firmware revision number in a fixed pattern

of LEDs. This indicates that default settings have been restored.

«
...
13
14
15
16
17
...
»

Summary of Contents for STS-K070





















Reviews:

No comments

Related manuals for STS-K070

Brand: Aaron Pages: 2

Brand: Aaron Pages: 3

Brand: Campbell Pages: 72

Brand: PAC Pages: 9

Brand: TCL Pages: 16

ACUSTICA H series

Brand: RCF Pages: 10

Brand: Spon Pages: 9

Brand: National Instruments Pages: 9

Brand: J.W. Davis Pages: 2

Brand: Fermax Pages: 16

Brand: ADLINK Technology Pages: 37

Brand: Audiovox Pages: 35

Brand: Kontron Pages: 2

Brand: Altec Lansing Pages: 1

Simplebus Diva FT SBC 07

Brand: Comelit Pages: 12

Brand: Teufel Pages: 20

Brand: NEXT pool Pages: 19

Brand: Contec Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands