Contacta STS-K070 Installation & User Manual Download Page 2 | Manualshive

Page: 2 / 20

background image

2

Contents

Product Overview

Components

Installation Instructions

Amplifier Installation

Speaker & Microphone Installation

Amplifier Setup

Using the System

Troubleshooting

3

3

6

7

8

12

14

16

Contacta has a policy of continuous product development, and therefore small specification

changes may not be reflected in this manual. Images, labels, packaging, accessories and product

colours are subject to change without notice.

«
1
2
3
4
...
»

Summary of Contents for STS-K070





















Reviews:

No comments

Related manuals for STS-K070

Brand: Xilica Audio Design Pages: 28

Brand: JBL Pages: 2

Brand: JBL Pages: 2

Brand: BAS-IP Pages: 18

Brand: VDO Pages: 2

Brand: Discount Car Stereo Pages: 5

Feeder/Deliming System EV9797-20

Brand: Everpure Pages: 2

Brand: Mobotix Pages: 25

Brand: Rain Bird Pages: 2

Brand: Alcad Pages: 28

Brand: Aiphone Pages: 2

Brand: Valcom Pages: 4

CompactModule CR2032

Brand: IFM Pages: 29

Brand: Hogtunes Pages: 12

Brand: dB Technologies Pages: 32

INSTYLE ECOUSTIC TANGO

Brand: unika vaev Pages: 2

Brand: Eaton Pages: 8

Brand: Kogan Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands