background image

EVS1000 Blot units 

 

5

 

 

Protein (Western) blotting buffers 

Transfer buffers must be made accurately using high grade reagents. Do not adjust the pH 
with acid or base as this will affect the properties of the buffer. pH will vary according to the 
purity of the reagents used.  

Triple buffer system 

For high efficiency transfer of Protein from acrylamide gels  

 

Anode 1 Buffer:  
0.3 M Tris base, 20% MeOH, pH 10.4:  
soak 4 standard grade filter paper sheets 

 

Anode 2 Buffer:  
0.025 M Tris base, 20% MeOH pH 10.4:  
soak 2 standard grade filter paper sheets 

 

Cathode Buffer:  
0.025 M Tris base, 0.04 M Caproic Acid, 20% MeOH pH 9.4:  
soak 6 standard grade filter paper sheets 

DNA (Southern) Blotting Buffer 

For high efficiency transfer of DNA from agarose gels. 

 

Soak 12 pieces of standard grade filter paper, 6 for the cathode, 6 for the anode in: 

o

 

50 x 1 M ethanolamine-glycine buffer, pH 11 

RNA (Northern) Blotting Buffer 

For high efficiency transfer of RNA from agarose gels. 

 

Soak 12 pieces of standard grade filter paper, 6 for the cathode, 6 for the anode in: 

o

 

50 x 0.2 M morpholinopropanesulfonic acid (MOPS) 

o

 

50 mM sodium acetate 

o

 

5 mM EDTA pH 7.0 

Nucleic acid transfer buffers 

Soak 12 pieces of standard grade filter paper, 6 for the cathode, 6 for the anode in: 

 

1 x TAE  40 mM Tris (pH 7.6), 20 mM acetic acid, 1 mM EDTA 

 

50 x (1l) dissolve in 750 ml distilled water: 

o

 

242 g Tris base (FW = 121) 

o

 

57.1 ml glacial acetic acid 

o

 

100 ml 0.5 M EDTA (pH 8.0) 

 

Fill to 1 litre with distilled water. 

Soak 12 pieces of standard grade filter paper, 6 for the cathode, 6 for the anode in: 

 

1 x TBE 89 mM Tris (pH 7.6), 89 mM boric acid, 2 mM EDTA 

 

10 x (1l) dissolve in 750 ml distilled water: 

o

 

108 g Tris base (FW = 121) 

o

 

55 g boric acid (FW = 61.8) 

o

 

40 ml 0.5 M EDTA (pH 8.0) 

 

Fill to 1 litre with distilled water. 

Transfer buffers 

Towbin Buffer with 20% methanol 

Soak 12 pieces of standard grade filter paper, 6 for the cathode, 6 for the anode in: 

 

0.025 M Tris base 

 

0.192 M glycine 

 

20% methanol 

 

pH 8.3 

 

 

Summary of Contents for EV1300













Reviews: