These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2012 by Conrad Electronic SE.
V1_1112_02-JH
5. Preparations for Installation
The product may only be installed and mounted by a qualified technician
(e.g. electrician), who is familiar with the relevant regulations (e.g. VDE,
German electrical wiring regulations)!
Improper work, carried out on the mains voltage, endangers not only your
own life but also the life of others! If you do not have the expertise required
for the installation, do not install it yourself but ask a qualified technician.
Observe the safety instructions!
• Only install the LED floodlight on a stable surface.
• The LED floodlight must be protected on the sub-distribution board by a 10/16 A fuse. An
earth leakage circuit breaker must be installed before this (FI protective switch).
• The LED floodlight must be disconnected from the power supply during installation. It is
not sufficient to just turn off at the light switch! Turn the power off and ensure that all the
poles are not carrying a current by removing the electric circuit‘s fuse, or switching off at
the circuit breaker. Secure it against unauthorised reconnection, e.g., with a danger sign.
In addition, switch off the associated ground fault circuit interrupter.
•
Check that the mains connection is current free with a suitable tester.
Only use a cable for the mains connection, which is suitable for being
permanently laid outdoors.
6. Installation
Note the information in the “Preparations for Installation” chapter, and the
installation illustrations in these operating instructions.
1.
Fasten the mounting bracket for the LED floodlight using at least two screws at a
suitable location on the wall. Depending on the installation location, suitable screws
and, if necessary, screw anchors are to be used.
The ideal installation height is between 2.5 and 3 m, depending where it is installed,
and the ambient conditions (position of the area to be lit).
When drilling mounting holes or screwing down, ensure that no existing electrical
cable, gas or water pipes are damaged!
2.
Remove the cover of the installation box on the back of the LED floodlight, by
unscrewing all four fixing screws from the cover. (see Ill. 1).
3. Loosen the cap nut for the cable gland. (see Ill. 2).
4. Remove the handle of the strain relief by unscrewing the two screws (see Ill. 2).
5. Remove the insulation on the mains cable to the required length. The earth conductor
should be slightly longer than conductor (L) and conductor (N) (see Ill. 3).
6. Insert the power cable through the cable gland.
7.
Connect the power cable with the terminal strip in the LED floodlight (see Ill. 4):
-
brown wire = L
-
blue wire = N
-
Green-yellow wire = PE / protective earth conductor / earthing symbol
The protective earth conductor must be connected!
If the LED floodlight is replacing an existing light and no protective earth
conductor is available, the LED floodlight must not be installed. First, draw a
new mains cable.
Where the protective earth is not connected, a fault with the mains voltage might
result in the metal housing of the LED floodlight becoming live. There is a risk of
a life-threatening electric shock!
Make sure only the minimum required length of the cable is stripped; otherwise
it could cause a short-circuit.
Also check the other screw connections on the terminal strip (for the connection
cables to the light electronics) and tighten them if necessary.
8. Fasten the mains cable to the strain relief. Attach the handle of the strain relief
previously removed and screw it firmly in place (see Ill. 4).
9. Screw the cable gland‘s cap nut tight so the rubber seal inside the cable gland is
sealed (see Ill. 4).
10.
Attach the cover previously removed and screw it firmly in place with four screws (see Ill. 5).
11.
Adjust the LED floodlight angle so that it illuminates the desired area. For this, loosen
both screws on the sides of the bracket, set the angle and tighten the screws again.
12. Switch on the mains voltage again and make sure that the lamp is working.
If the LEDs in the LED floodlight do not light up, switch off the power immediately
and please have the connection of the lamps checked by a technician (e.g.
electrician)!
7. Maintenance and Care
• The LED floodlight is maintenance-free, this is why you should never open or dismantle
it (apart from the connection / installation described in this operating manual).
•
You should occasionally clean dust and dirt off the glass plate on the lamp to ensure
proper functioning.
• Switch off the LED floodlight or disconnect it from the mains voltage before cleaning. Let
it cool down sufficiently.
• The exterior of the LED floodlight should only be wiped with a clean, soft, dry cloth.
Where it becomes very dirty, use a cloth which is slightly moistened with lukewarm water.
•
Do not use aggressive cleaning agents or chemical solutions that could damage the
housing (discolouring) or impair operation.
•
Do not press too hard on the housing or the glass plate, as scratches might appear.
Never spray water e.g. with a garden hose or a high-pressure cleaner, at the
LED floodlight!
8. Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations.
9. Technical Data
Operating voltage:
110 – 240 V/AC, 50/60 Hz
Power consumption:
max. 3.8 W
Protection class:
I
Protection type:
IP65
Installation location:
Interior/exterior
Light source:
60 LEDs with 0.06 W each, not exchangeable
Colour temperature:
6,000 – 7,000 K
Luminous flux:
210 lm
Beam angle:
60°
Ambient temperature:
-10 to +50 °C
Dimensions (W x H x D): 102 x 135 x 55 mm
Weight:
approx. 306 g
