2
Operating Instructions
Dummy Vehicle Camera with Flashing LED
Item no: 2357056
1 Intended use
The product is an imitation security camera which acts as a deterrent to potential thieves.
It has a blinking LED to make it look like the camera is active.
A windscreen sticker is included as an additional deterrent.
The product is intended for indoor use only. Do not use it outdoors.
Contact with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product may be damaged.
Improper use can result in short circuits, fires, or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product available to
third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights reserved.
2 Delivery contents
■
Product
■
Security sticker
■
Operating instructions
3 Latest product information
Download the latest product information at
www.conrad.com/downloads
or scan the QR code shown. Fol-
low the instructions on the website.
4 Description of symbols
The symbol with the exclamation mark in the triangle is used to indicate important informa-
tion in this document. Always read this information carefully.
5 Safety instructions
Read the operating instructions carefully and especially observe the safety informa-
tion. If you do not follow the safety instructions and information on proper handling,
we assume no liability for any resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
5.1 General
■
The product is not a toy. Keep it out of the reach of children and pets.
■
Do not leave packaging material lying around carelessly. This may become dangerous playing mater-
ial for children.
■
If you have questions which remain unanswered by this information product, contact our technical
support service or other technical personnel.
5.2 Handling
■
Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
■
Consult an expert when in doubt about the operation, safety or connection of the appliance.
5.3 Operating environment
■
Do not place the product under any mechanical stress.
■
Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
■
Protect the product from high humidity and moisture.
5.4 (Rechargeable) Batteries
■
Correct polarity must be observed while inserting (rechargeable) batteries.
■
The (rechargeable) batteries should be removed from the device if it is not used for a long period of
time to avoid damage through leaking. Leaking or damaged (rechargeable) batteries might cause acid
burns when in contact with skin, therefore use suitable protective gloves to handle corrupted (re-
chargeable) batteries.
■
(Rechargeable) batteries must be kept out of reach of children. Do not leave (rechargeable) batteries
lying around, as there is risk, that children or pets swallow them.
■
All (rechargeable) batteries should be replaced at the same time. Mixing old and new (rechargeable)
batteries in the device can lead to (rechargeable) battery leakage and device damage.
■
(Rechargeable) batteries must not be dismantled, short-circuited or thrown into fire. Never recharge
non-rechargeable batteries. There is a risk of explosion!
6 Setting up
6.1 Insert batteries
1. Rotate the casing to line the arrows up where it is marked:
Align to open
.
2. Pull the sections apart.
3. Open the batteries compartment by lifting up where it is marked:
Open
.
4. Insert the batteries matching polarities shown inside the compartment.
5. Close the compartment.
6.2 Mounting
Note:
The mounting surface should be clean, dry, and free from debris.
■
The product should be mounted to the front windscreen with the imitation camera lens / LED facing
out of the vehicle.
■
Adjust the camera angle by rotating the case.
6.3 Security sticker
Note:
The mounting surface should be clean, dry, and free from debris.
■
The security sticker can be applied to the front or rear windscreen as an additional deterrent.
■
The adhesive should be applied to the glass on the inside the vehicle.
■
Press the product against the surface for approximately 1 minute to help the adhesive set.
7 Operation
■
There is no ON/OFF switch.
■
The product switches ON when batteries are inserted.
■
The LED blinks at regular intervals.
■
The product switches OFF when batteries are removed.
8 Cleaning and care
Clean the product with a dry, fibre-free cloth.
NOTICE! Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
9 Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
Remove any inserted (rechargeable) batteries and dispose of them separately from the
product. You as the end user are required by law (Battery Ordinance) to return all used (re-
chargeable) batteries. Disposing of them in the household waste is prohibited.
Contaminated (rechargeable) batteries are labeled with this symbol to indicate that disposal
in the domestic waste is forbidden. The designations for the heavy metals involved are: Cd =
Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable) batteries, e.g. below the trash
icon on the left).
You thus fulfill your statutory obligations and contribute to the protection of the environment.
10 Technical data
Power supply ......................................... 2x 1.5 V AAA batteries
Battery life............................................... approx. 1 year (continuous use)
Operating temperature .......................... -20 to +45 °C
Operating humidity ................................ 0 – 85 % RH (non-condensing)
Storage temperature ............................. -20 to +45 °C
Storage humidity .................................... 0 – 85 % RH (non-condensing)
Dimensions (L x W x H) ......................... 108 x 32 x 39 mm
Weight .................................................... 46 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE
*2357056_V1_0521_dh_mh_en
