background image

Copyright 

© 

2021 

congatec 

GmbH 

 

      GEVAm03 

       

3/65

Preface

This user’s guide provides information about the components, features, and connectors available on the conga-HPC/EVAL-Client evaluation 
carrier board.

Software Licenses

Notice Regarding Open Source Software

The congatec products contain Open Source software that has been released by programmers under specific licensing requirements such as 
the “General Public License“ (GPL) Version 2 or 3, the “Lesser General Public License“ (LGPL), the “ApacheLicense“ or similar licenses. 

You can find the specific details at https://www.congatec.com/en/licenses/. Search for the revision of the BIOS/UEFI or Board Controller 
Software (as shown in the POST screen or BIOS setup) to get the complete product related license information. To the extent that any 
accompanying material such as instruction manuals, handbooks etc. contain copyright notices, conditions of use or licensing requirements that 
contradict any applicable Open Source license, these conditions are inapplicable. 

The use and distribution of any Open Source software contained in the product is exclusively governed by the respective Open Source 
license. The Open Source software is provided by its programmers without ANY WARRANTY, whether implied or expressed, of any fitness for 
a particular purpose, and the programmers DECLINE ALL LIABILITY for damages, direct or indirect, that result from the use of this software. 

OEM/ CGUTL BIOS

BIOS/UEFI modified by customer via the congatec System Utility (CGUTL) is subject to the same license as the BIOS/UEFI it is based on. You 
can find the specific details at https://www.congatec.com/en/licenses/.

Disclaimer

The information contained within this user’s guide, including but not limited to any product specification, is subject to change without notice.

congatec GmbH provides no warranty with regard to this user’s guide or any other information contained herein and hereby expressly disclaims 
any implied warranties of merchantability or fitness for any particular purpose with regard to any of the foregoing. congatec GmbH assumes 
no liability for any damages incurred directly or indirectly from any technical or typographical errors or omissions contained herein or for 
discrepancies between the product and the user’s guide. In no event shall congatec GmbH be liable for any incidental, consequential, special, 
or exemplary damages, whether based on tort, contract or otherwise, arising out of or in connection with this user’s guide or any other 
information contained herein or the use thereof.

Summary of Contents for conga-HPC/EVAL-Client


































































Reviews: